629516
57
Zoom out
Zoom in
Previous page
1/80
Next page
Installation Menu
57
You should only make changes in this menu if the receiver is connected
to a different receiving system with different properties or if changes
have been made to the receiving system.
You should therefore carefully follow the instructions for your satellite
system. However, before each change you should note the settings on
the form at the end of this operating manual.
You reach the “DiSEqC[UFO] Setup” menu using the

keys and the
key in the Installation menu.
22 kHz Signal
This menu option is used to specify whether the 22 kHz signal is to be
used to switch between the upper and lower frequency ranges for a
satellite (low/high) or between two satellite positions.
Tone Burst and DiSEqC
TM
Signal
If more than four control criteria are requried in a receiving system, a
DiSEqC™ control signal is required.
Which of the setting options - Tone Burst or DiSEqC™ - is required
depends on the components of the receiving system.
You should therefore refer to the descriptions of the existing
components (switching matrices) of the receiving system.
Switching states for setting:
22 kHz Signal
----------->
Pos. A/B:
and
Tone Burst
----------->
Opt. A/B:
Pos
Tone Burst
22 kHz
1
0
Off
2
0
On
3
1
Off
4
1
On
Switching states for setting:
22 kHz Signal
----------->
High/Low
and
Tone Burst
----------->
Pos. A/B:
Low
22 kHz
Off
High
22 kHz
On
Pos. 1
Tone Burst
0
Pos. 2
Tone Burst
1
Switching states for setting:
22 kHz Signal
----------->
Pos. A/B:
and
Tone Burst
----------->
High/Low
Low
Tone Burst
0
High
Tone Burst
1
Pos. 1
22 kHz
Off
Pos. 2
22 kHz
On
If the receiver is connected to a DiSEqC™ switching matrix, set the
menu option to “On”.
The switching criteria and the input assignment of the
DiSEqC™
switching matrices must be observed. You should therefore follow
the description of the switching matrices or contact the engineer
who installed the receiving system.
DiSEqC
TM
DiSEqC
TM
Repeat
If the receiver is operated in a receiving system with two or more
DiSEqC™ switching matrices connected in series (cascaded), the
DiSEqC™ command must be repeated.
In this case, set the DiSEqC™ Repeat menu option to “1” or “2”.
Default setting: “Off”
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein UFD 170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein UFD 170 in the language / languages: English as an attachment in your email.

The manual is 5,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info