473814
15
Zoom out
Zoom in
Previous page
1/68
Next page
15
Ensure before starting adhesive work that the temperature of materials to be glued and the sealant
is between +5 °C and +40 °C. Prepare all necessary fastening elements and tools.
Prepare the tube of adhesive sealant in accordance with the instructions enclosed with the tube.
Remove the roof gland (Fig. A) and apply the adhesive sealant evenly to the underside of the roof
gland ange.
Replace the roof gland in the drilled hole and press it rmly against the roof of the vehicle.
Apply the adhesive sealant evenly to the underside of the mounting plate, completely covering the
area within the circular groove (Fig. D).
This area of the vehicle roof must be completely coated with adhesive in order to achieve the
necessary bonding force.
Place the mounting plate onto the roof of the vehicle, as you did previously when marking out the
drilled holes.
Make sure that the arrow on the mounting plate points forward in the direction of travel.
The fastening holes must be perfectly aligned with the prepared holes in the roof.
Fasten the mounting plate in place with the prepared screws, evenly tightening six screws across the
diagonals.
Note: The adhesive sealant used is capable of lling small gaps caused by the curvature of the
vehicle roof. However, you should ensure that the mounting plate is not bent by tightening
the screws.
Remove any adhesive sealant that leaks out at the sides with a clean cloth or if necessary with
Sika ex
®
remover (available from specialist dealers). Do not use cleaning agents or thinners
containing solvents, as this could damage the sealant applied under the mounting plate. Use only
cleansing paste and water to clean your hands.
Secure the cable gland from inside the vehicle by tightening the ribbed nut supplied (Fig. A).
Note that the curing of the adhesive sealant depends on the ambient temperature and the humidity.
Final strength is reached only after approx. ve days. However, this need not restrict further
installation work, since the mounting plate is held in place by the tightened screws.
INSTALLATION AND CONNECTION
VARIANT WITH CABLE GLAND UNDERNEATH THE TURNTABLE
Feed the ends of the cables with the connectors as far as possible through the cable duct into the
interior of the vehicle.
INSTALLATION OF TURNTABLE
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein MobiSet 2 digitaal CAP 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein MobiSet 2 digitaal CAP 610 in the language / languages: English as an attachment in your email.

The manual is 3,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein MobiSet 2 digitaal CAP 610

Kathrein MobiSet 2 digitaal CAP 610 User Manual - German - 68 pages

Kathrein MobiSet 2 digitaal CAP 610 User Manual - Dutch - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info