631710
21
Zoom out
Zoom in
Previous page
1/36
Next page
21
Installation and connection
Laying cables and connecting the turntable HDP 171
Lay the control cable (8-pole Western connector), the coaxial cable
and the power supply cable (2-pole connector) to the UFD 170.
Avoid laying the cables across sharp edges and secure the cable
against possible abrasion points.
Connect the control cable to the “POSITIONER” connecting socket
on the rear of the UFD 170. Repeat for the power supply cable,
which has to be connected to the two “POWER OUT” cables.
Connect the coaxial cable (coming from the turntable) to the “IF IN”
F socket on the rear panel of the UFD 170.
• Place the infrared sensor close to or directly on top of the TV set
and lay the cable to the UFD 170. Connect the 6-pole Western
connector on the rear to the socket marked “IR REMOTE IN”.
Note for CAP 310: Lay the AV cinch enclosed with the CAP 310 from the HTV 115 TV
set AV cinch cable to the UFD 170 receiver.
Connecting the UFD 170 to the on-board power network
Isolate the on-board network (master switch “off” or disconnect negative
pole of on-board network battery) before commencing the following
work:
Connect the included 3-pin cable to the receiver’s “POWER IN”
plug connector.
Make sure that the “inline“ integrated fuse (15 A) of the cable is
completely plugged in an intact. If the fuse responds, the source
of the fault must rst be eliminated. The fuse may only ever be
replaced by a fuse with the same rated value (15 A).
The fuses in the cable and in the receiver may never be bridged
– cable re hazard!
At the connecting point for the positive and negative wires, the
voltage may not fall below 10.9 V even with a load of 12 A. Otherwise
optimum functioning can no longer be guaranteed.
• Connect the connecting cable wires marked “EARTH” (white wire)
and “+12 V” (brown wire) to the corresponding battery contacts.
Note for CAP 210: Lay the AV cinch enclosed with the CAP 210 to the Scart cable.
Here you must absolutely note the assignment of the connectors!
The cinch connector must be assigned to the UFD 170 and the
Scart connector to the TV set. Reversal is not possible – unit will not
function!
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kathrein CAP 210 - MobiSet 2 digital at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kathrein CAP 210 - MobiSet 2 digital in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Kathrein CAP 210 - MobiSet 2 digital

Kathrein CAP 210 - MobiSet 2 digital Installation Guide - Dutch - 40 pages

Kathrein CAP 210 - MobiSet 2 digital Installation Guide - French - 36 pages

Kathrein CAP 210 - MobiSet 2 digital Installation Guide - Spanish - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info