Manual Karcher HDS 13-20 De Tr1 (page 29 of 512) (All languages)

726238

Zoom out

Zoom in

1/512

- 9

If the appliance is not used for an ex-

tended period and if there is frost, re-

move the battery and store it in a loca-

tion protected from frost.

With external water supply: Disconnect

the water hose from the water supply.

Set the power switch to "0/OFF“ (burner

off).

Unpressurize the appliance.

Set the power switch to the operating

mode "frost protection".

HDS 13/20, HDS 17/20 only:

Set the detergent dosing valve to maxi-

mum. Pull the detergent suction hose

out of the detergent container and store

it in such a way that it can be evacuated.

Open the supply tap of the water tanks

and the drain tap in order to completely

drain the device. The filling level indica-

tor of the water tanks dips completely.

Close the supply tap of the water tanks

and the drain tap.

Disconnect the trigger gun from the

high-pressure hose.

Connect the high-pressure hose to the

frost protection inlet.

Connect the water hose to the return

flow of the frost protection.

Prepare the antifreeze in the antifreeze

container. Select the mixing ratio of the

water/antifreeze as per the instructions

of the antifreeze manufacturer.

Check the antifreeze concentration with

a commercially available antifreeze

tester and adapt if necessary.

Open the filling hole of the float contain-

er. In order to do so, loosen the wing

screw and push the cover to the left.

Fill 20 litres of antifreeze into the float

container and close the filling hole.

Align the actuation lever of the ball tap

for antifreeze vertically.

Place the actuation lever of the return

flow valve ball tap parallel to the travel

direction (20L).

With cold engine only:

To preheat the motor, turn the key

switch to the left and hold it until the in-

dicator light preheating goes out.

Turn key switch to position "I". The indi-

cator lamp for operational readiness

lights up.

The control voltage is switch on and the

display shows the operating status "An-

tifreeze".

Turn the key switch to the right until the

motor is running.

The antifreeze liquid is pumped through

the appliance in a circuit.

Lead the residual water via the frost

protection hose into the anti-freeze con-

tainer.

As soon as antifreeze exits the anti-

freeze hose, put the operating lever of

the frost protection ball tap in the hori-

zontal position and wait for 5 seconds.

Switch off the motor.

Set the power switch to "0/OFF“ (burner

off).

Note: Prior to operation, the antifreeze

must be pumped from the high-pressure

system back into the antifreeze container.

Align the actuation lever of the ball tap

for antifreeze vertically.

Connect the high-pressure hose to the

frost protection inlet.

Connect the water hose to the return

flow of the frost protection.

Open the filling hole of the float contain-

er. In order to do so, loosen the wing

screw and push the cover to the left.

Fill 20 litres of fresh water into the float

container and close the filling hole.

Set the power switch to the operating

mode "frost protection".

With cold engine only:

To preheat the motor, turn the key

switch to the left and hold it until the in-

dicator light preheating goes out.

Turn key switch to position "I". The indi-

cator lamp for operational readiness

lights up.

The control voltage is switch on and the

display shows the operating status "An-

tifreeze".

Turn the key switch to the right until the

motor is running.

The antifreeze fluid is forwarded from

the float container into the antifreeze

container with fresh water.

Rinse for approx. 2 minutes until the an-

tifreeze container is filled.

Switch off the motor.

Set the power switch to "0/OFF“ (burner

off).

Frost protection battery

Antifreeze rinse in the circuit (high

pressure pump)

Pumping antifreeze out of the high

pressure system

29EN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher HDS 13-20 De Tr1 in the language / languages: All languages as an attachment in your email.

The manual is 111,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher HDS 13-20 De Tr1 Manual

Product: