Manual Karcher B50 W (page 18 of 296) (All languages)

804748

Zoom out

Zoom in

1/296

18 English

6. Adjust the screw so that the spirit level indicator is

between the two lines.

7. Tighten the M 12 nut while holding the

M 10 hexagon head screw with an open-end

wrench.

8. To check the new setting, move the device forward

a short distance in suction mode with the suction bar

lowered and observe the spirit level. Repeat the ad-

justment process if necessary.

Adjusting the height

The height adjustment affects the bending of the suction

lips on contact with the floor.

Note

Standard setting: 3 washers above, 3 washers below

the suction bar.

Uneven floor: 5 washers above, 1 washer below the

suction bar.

Very smooth floor: 1 washer above, 5 washers below

the suction bar.

1. Unscrew the nuts.

Illustration L

1Nut

2Washer

3Spacer roller with holder

2. Place the desired number of washers between the

suction bar and the spacer roller.

3. Fit the remaining unused washers above the spacer

roller.

4. Screw on the nut and tighten.

5. Repeat the entire procedure at the second spacer

roller.

Note

Set both spacer rollers to the same height.

Adjusting the side pull of the brush

(Only with D 51 cleaning head)

If the device pulls to one side during cleaning, this can

be remedied by adjusting the brush tilt.

Note

After changing the brush/pad, it may be necessary to re-

adjust the side pull.

1. Adjust the brush tilt rotary knob until the device

moves straight ahead.

Illustration M

1Brush inclination rotary knob

Switching on the device

1. Assume a seated position.

2. Turn the key-operated switch to "1".

The display shows the following one after the other:

●Period of time until the next after-sales Customer

Service

●Software version, control panel

●Battery charge state and number of operating hours

Driving

Note

The device is constructed so that the cleaning head pro-

trudes to the right. This makes it possible to work clearly

and close to the edge.

1. Insert the Intelligent Key.

2. Pivot the suction bar lowering lever upwards.

3. Press the raise /lower cleaning head pedal down

and latch it towards the right.

4. Set the program switch to the desired program.

5. Drive the device.

a Push the driving lever forward.

The device moves forward.

b Push the driving lever backwards.

The device moves in reverse.

Note

The device moves only when the driving lever is moved

by 5°.

6. Release the driving lever.

The device stops.

Cleaning

ATTENTION

Risk of damage

The floor covering can be damaged if the device is op-

erated on the same spot for a long time.

Do not operate the device continuously on the same

point.

1. Insert the Intelligent Key.

2. Set the program switch to the desired cleaning pro-

gram.

3. Pivot the lever downwards to lower the suction bar.

4. Press the cleaning head raise/lower pedal down,

move it to the left and let it go up.

5. Push the driving lever forward and drive over the ar-

ea to be cleaned.

Note

When the waste water tank is full, the float switch closes

the suction opening and the suction turbine runs at a

higher speed. In this case, switch off the vacuuming

function and drive to the location for emptying the waste

water tank.

Finishing operation

Finishing cleaning

1. Turn the water quantity regulating knob to "OFF"

(not for the DOSE version).

2. Release the driving lever.

3. Press the raise /lower cleaning head pedal down

and latch it towards the right.

4. Continue moving a short distance.

The residual water is vacuumed up.

5. Pivot the suction bar lowering lever upwards.

Draining the waste water

몇WARNING

Environmental pollution!

Environmental pollution due to improper disposal in

waste water.

Observe the local waste water treatment regulations.

1. Remove the drain hose from the support and lower

it over a suitable collecting device.

Illustration N

2. Press the dosing unit together or kink the hose.

3. Open the dosing unit cover.

4. Drain the waste water. Regulate the water volume

by pressing or kinking.

5. Rinse the waste water tank with clear water.

Waste water tank flushing system

1. Remove the waste water drain hose from the holder

and lower it over a suitable collecting device.

2. Open the dosing unit cover at the drain hose.

3. Open the waste water tank cover.

4. Pull the flexible cap off the flushing system.

5. Connect the water hose to the flushing system.

Illustration O

1Lock

2Tank ventilation flap

3Flushing system water connection

6. Close the waste water tank cover.

7. Open the water supply and flush the waste water

tank for about 30 seconds.

If necessary, repeat the flushing process 2 - 3 times.

8. Close the water supply and disconnect the hose

from the device.

9. Reattach the flexible cap to the water inlet of the

flushing system.

10. Close the cover of the waste water tank. Press the

tank ventilation flap in so that a gap remains open

and the waste water tank can dry.

11. Push the waste water drain hose into the holder and

closed the cover of the dosing device.

Draining fresh water at the cap

1. Open the fresh water tank cap.

2. Drain the fresh water.

3. Clean the filter.

4. Fit the fresh water tank cap.

Draining fresh water via the filling level indicator

1. Remove the filling level indicator hose from the hold-

er and pivot it down.

2. Reattach the hose.

Emptying the coarse dirt container

(R cleaning head only)

1. Lift the coarse dirt container and pull it out.

Illustration P

1Coarse dirt container

2. Empty the coarse dirt container and clean it if nec-

essary.

3. Reinstall the coarse dirt container.

Parking the device

1. Turn the program switch to position "0".

2. Remove the Intelligent Key.

3. Press the raise/lower cleaning head lever down and

latch it towards the right.

4. Pivot the suction bar lowering lever upwards.

5. Secure the device against rolling away.

6. Close the cover of the waste water tank. Press the

tank ventilation flap in so that it engages in the

groove of the fresh water tank so that the waste wa-

ter tank can dry.

7. Charge the battery if necessary.

Transport

DANGER

Driving on slopes

Risk of injury

Observe the maximum permissible gradient when oper-

ating the device on slopes for loading and unloading

purposes (see chapter "Technical data").

Drive slowly.

몇CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during transport.

Only load the device with the dirt and fresh water tanks

empty.

Only load the device with the assistance of another per-

son or by using the drive.

1. Press the raise/lower cleaning head pedal down and

latch it towards the right.

2. Remove the brushes to avoid damage.

3. Remove the suction bar from the device.

4. When transporting in vehicles, secure the device

against slipping and tipping over using the transport

eyelets according to the respectively applicable

guidelines.

Illustration Q

Storage

몇CAUTION

Failure to observe the weight

Risk of injury and damage

Be aware of the weight of the device during storage.

ATTENTION

Frost

Destruction of the device through freezing water

Drain all water from the device.

Store the device in a frost-free location.

●This device may only be stored indoors.

●Fully charge the batteries before storing them for a

long period.

●Fully charge the batteries at least every month dur-

ing storage.

Care and maintenance

DANGER

Inadvertently starting up device

Risk of injury

Turn the program switch to the "0" position.

Remove the Intelligent Key prior to all work on the device.

Pull out the charger mains plug.

Drain and dispose of the waste water and fresh water.

Safety inspection/maintenance contract

You can agree on regular safety inspections or close a

maintenance contract with your dealer. Please seek ad-

vice on this.

Maintenance intervals

Each time after use

ATTENTION

Improper cleaning

Risk of damage.

Do not spray the device with water.

Do not use aggressive cleaning agents.

Drain the waste water.

Clean the waste water tank with the waste water

tank flushing system.

Remove the coarse dirt filter from the waste water

tank and clean it.

Check the turbine screen, remove it if necessary

and clean it.

Clean the exterior of the device using a damp cloth,

wetted with a mild washing lye.

Only with R cleaning head: Remove the coarse dirt

container and empty it.

Only with R cleaning head: Clean the water distribu-

tion strip.

Check the suction lips, check for wear and replace if

necessary.

Clean the squeegee blades on the cleaning head,

check for wear and replace if necessary.

Clean the brushes, check for wear and replace if

necessary.

Close the cover of the waste water tank. Press the

tank ventilation flap in so that a gap remains open

and the waste water tank can dry.

Charge the battery.

Lead-acid battery:

If the charging state of the battery is below 50%,

charge the battery fully and without interruption.

If the charging state of the battery is above 50%,

only recharge the battery if the entire operating

duration will be required when next used.

Li-Ion battery:

Recharge as necessary.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Karcher B50 W in the language / languages: All languages as an attachment in your email.

The manual is 34.13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Karcher B50 W Manual

Product: