Manual JVC RX-ES1SL (page 20 of 75) (English)

495432

Zoom out

Zoom in

1/75

RX-ES1SL

Speaker settings

Setting the speakers information

automatically—Smart Surround Setup

The distance from your listening point to the speakers is one of the

important element to obtain the best possible sound effect for the

Surround/DSP modes.

You need to set the delay time of the center and surround speakers

relative to the front speakers so that sounds through all the speakers

can reach you at the same time (see also page 18).

By using Smart Surround Setup, the speaker delay time and output

level are automatically calculated by one simple action—clapping

hands.

• To use Smart Surround Setup effectively, connect both the center

and surround speakers.

• You can also set the crossover frequency, the low frequency effect

attenuator and the dynamic range compression manually (see page

18).

• When you change your speakers, do the following steps again.

From the remote control ONLY:

To obtain the best possible surround effect from Surround/DSP modes (see pages 28 to 33), you need to set up the speaker and subwoofer

information after all the connections are completed. You can set the speaker information using one of the following three methods.

Smart Surround Setup: Set the speakers information automatically by one simple action—clapping hands. The delay time and output level for

the center and surround speakers are set automatically.

Quick Setup: Set the speakers and subwoofer information quickly by entering the use of the subwoofer, the number of the speakers,

and your room size.

Manual Setup: Set the speakers and subwoofer information manually.

• Before starting the speaker setting, connect and position the speakers and subwoofer (see page 7) and turn on the receiver.

Confirm “SETTING UP” stops flashing and clap

your hands over your head once while “SETTING

UP” appears on the display.

The receiver starts detecting the level of the sound coming

through all speakers (except the subwoofer).

After detecting the sound, one of the following indications appears

on the display.

SUCCESSFUL: Sound of your clapping is successfully

detected. The receiver sets the delay time

and the output level of the center and

surround speakers automatically.

SILENT: The receiver cannot detect sound from some

speakers.

SILENT-ALL: The receiver cannot detect any sound from all

speakers.

FAILED: The receiver cannot detect both right and left

channels for the front and/or surround

speakers correctly.

• When the receiver cannot detect the sound correctly (“SILENT,”

“SILENT-ALL” or “FAILED” appears on the display), “SETTING

UP” appears on the display again then repeat step

• The speaker delay time and output levels are set automatically

when:

—the receiver detects the sound as “SILENT” twice in

succession.

—the receiver detects the sound as “SILENT” at the third time

after detecting “SILENT”, “SILENT-ALL” and/or “FAILED”

twice.

• When the receiver detects the sound as “SILENT-ALL” or

“FAILED” three times, “MANUAL” appears on the display. Set

the speaker and subwoofer information using Quick Setup (see

page 16) or Manual Setup (see page 17), and the speakers'

output levels for the center and surround speakers (see pages

31 to 33).

To cancel Smart Surround Setup, press SMART S. SETUP while

“SETTING UP” flashes on the display.

• Any other operations cannot be done after “SETTING UP” stops

flashing. Complete the Smart Surround Setup.

NOTES

• You need to set the subwoofer information and output level

manually (see pages 17 and 21).

• When you use Smart Surround Setup, the speaker delay time and

output levels you have set before will be ineffective.

• Set the speakers information using Quick Setup (see page 16) or

Manual Setup (see page 17), and the speakers’ output levels for

the center and surround speakers (see pages 31 to 33) when:

—you like to change the speaker setting made by Smart Surround

Setup

—Smart Surround Setup is not done correctly due to some factors

such as the environment, speaker types and clapping strength.

• Smart Surround Setup will not be done correctly if your body or

other object blocks the sound.

• Do not clap your hands hard because it may hurt your hands.

When operating the

receiver using the remote

control, always set the

mode selector to AUDIO/

TV/VCR/STB.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is

canceled before you finish, start from step

again.

Take your position where you listen to the sound.

ANALOG

SUBWFR

VOL

DIGITAL

SURROUND

DIGITAL

PRO LOGIC

RX-ES1 HOME CINEMA CONTROL CENTER

STANDBY / ON STANDBY

TV DIRECT SETTING ADJUST SURROUND

DVD MULTI DVD STB VCR TV FM / AM

SET / TUNER PRESET

SOURCE SELECTOR MASTER VOLUME

PHONES

/ MULTI JOG

DVD

AUDIO/TV

/VCR/STB

AUDIO

ZOOM

ANGLE

REPEAT

DIMMER

SUBWFR CENTER L RSURR

BASS BOOST

A.POSITION

SMART S. SETUP

SLEEP CANCEL

SURROUND

ANALOG/DIGITAL

TV RETURN 100

BASS TREBLE

SUBTITLE RETURN

TITLE/GROUP

BASS TREBLE

123

VFP

INPUT

TONE

TEST EFFECT

DECODE

789

0 +10

Press and hold SMART S. SETUP.

“SETTING UP” flashes on the display.

15-20.RX-ES1&XV-N55[B]f 03.2.18, 1:47 PM15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JVC RX-ES1SL in the language / languages: English as an attachment in your email.

The manual is 3,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JVC RX-ES1SL Manual

Product: