138393
28
Zoom out
Zoom in
Previous page
1/72
Next page
Filename [XV48EK_07S-VHS.fm]
Masterpage:Left+
Page 28 November 18, 2004 10:44 pm
OPERATIONS ON VHS DECK (cont.)
28
When Programmes Overlap Each
Other
If “PROGRAM OVERLAPPED” appears, you have another
programme overlapping the programme you have just made.
The Programme Check screen appears and conflicting
programmes will start blinking.
Example: Programme 1 (you have just made) and
Programme 4 overlap each other.
A
Confirm the overlapping programmes.
Overlapping programmes blink on the TV screen.
B
Select the programme to modify.
Press rt, then press ENTER or e.
You can only select one of the overlapping programmes.
NOTE:
If you do not mind this overlap, press PROG to finish the timer
programme setting. The programme with the lower programme
number will be recorded and the other one will not be recorded
correctly. If no changes are made for approximately 1 minute,
the unit will return to the normal screen.
C
Cancel or change programme setting.
To cancel a programme, press & when the Programme
screen you do not want is shown. “PROGRAM
COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears.
To change a programme, press the appropriate button:
START +/–, STOP +/–, DATE +/, PR +/–, PDC (number
key “7”), DAILY (number key “8”), WEEKLY (number key
“9”) and/or p when the Programme screen on which
you want to make changes is shown, then press ENTER.
“PROGRAM COMPLETED” appears on the TV screen for
about 5 seconds, then the normal screen appears.
NOTE:
If the overlap is not yet solved, or another overlap occurs with
the timer programme setting after making the last correction on a
programme, the conflicting programmes will be shown on the
Programme Check screen again. Repeat the above steps again
until the overlap is solved.
Automatic Satellite
Programme Recording
This function allows you to automatically record a
satellite programme which is timer-programmed on your
external satellite receiver. Connect a satellite receiver to
the unit’s L-2 IN/DECODER connector and programme
the timer on the satellite receiver. The unit starts or stops
recording by the signals input from the satellite receiver.
After recording, the unit’s power shuts off automatically.
Slide to the
right.
ATTENTION
Be sure not to turn on the satellite receiver before the
programme is executed; otherwise, the unit will start
recording when the satellite receiver’s power is turned on.
If you have connected another appliance other than a
satellite receiver to the L-2 IN/DECODER connector, be
sure not to engage the Automatic Satellite Programme
Recording mode; otherwise, the unit will start recording
when the connected appliance’s power is turned on.
Automatic Satellite Programme Recording and timer-
recording cannot be done at the same time.
XV48EK_01.book Page 28 Thursday, November 18, 2004 10:45 PM
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr xv48ex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr xv48ex in the language / languages: English, German as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info