136123

JVC hr dvs 2 Manual

10
Zoom out
Zoom in
Previous page
1/84
Next page
10
IMPORTANT
Ⅲ In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work
properly. If the Guide Program numbers are not set properly, when you timer-record a TV programme using the VIDEO Plus+
system, the recorder will record a TV programme of a different station. When programming the timer using the VIDEO Plus+
system, be sure to check that the preset position corresponding to the broadcasting station you wish to record has been
selected (੬ pg. 20, "VIDEO Plus+ Timer Programming").
Ⅲ Your video recorder memorizes all detected stations even if reception of some of them is poor. In these cases picture quality
may be poor. To delete those stations which have an unacceptable picture ੬ "Delete A Channel" on page 67.
Ⅲ If any of the above problems occur, refer to pages 66 – 69 to input station names (੬ "Set Stations") or delete unnecessary
stations (੬ "Delete A Channel"). You can also change station preset positions (੬ "Change Station Preset Position").
Auto Set Up/Preset Download results appear on the display panel
When neither auto channel set nor auto clock set has been completed successfully, "– –:– –"
will be displayed.
* You can check if the Guide Program numbers have been set correctly when you perform the VIDEO Plus+ Timer Programming
(੬ pg. 20); if the correct preset position number is displayed in step 4, this confirms that the Guide Program number for the
PlusCode number you enter in step 3 has been set correctly.
A If both auto channel set and auto clock set have been performed successfully:
1 Turn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the recorder's memory
by using the PR button(s).
● If station names (ID — ੬ pg. 70) have also been stored in the recorder's memory, the station name will be displayed at the
top left corner of the screen for about 5 seconds each time the recorder is tuned to a different station.
● If you want to set the tuner manually such as to add or skip channels, to change preset positions, or to set or change station
names, see pages 66 – 69.
Now you have finished the basic set up and can use your recorder for both playback and recording.
B If auto channel set has succeeded but auto clock set has not:
1 Turn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the recorder's memory
by using the PR button(s).
● If station names (ID — ੬ pg. 70) have also been stored in the recorder's memory, the station name will be displayed at the
top left corner of the screen for about 5 seconds each time the recorder is tuned to a different station.
● If you want to set the tuner manually such as to add or skip channels, to change preset positions, or to set or change station
names, see pages 66 – 69.
2 Perform "Clock Set" on page 72.
Now you have finished the basic set up and can use your recorder for both playback and recording.
C If both auto channel set and auto clock set have failed:
1 Make sure that the TV aerial cable is connected properly to the recorder, or that the 21-pin SCART cable is connected
properly between TV and the recorder. Turn off the recorder power once, then turn the recorder power back on again.
2 Perform "Auto Set Up" on page 8 or "Preset Download" on page 9.
If you have any difficulty with the above procedures call the JVC Customer Service Hot Line
on 020 8208 7654
A
B
C
When both auto channel set and auto clock set have been completed successfully the
correct current time will be displayed after the OK button is pressed in item
2
on page 8 or
after performing item
2
on page 9.
When auto channel set has been completed successfully but auto clock set has not, "(PR)1"
will be displayed after the OK button is pressed in item
2
on page 8 or after performing
item
2
on page 9.
QUICK SET UP GUIDE (cont.)
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC hr dvs 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC hr dvs 2 in the language / languages: English as an attachment in your email.

The manual is 2,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info