34423
41
Zoom out
Zoom in
Previous page
1/96
Next page
41
5. PREPARATIONS
LIGHT
ON
OFF
COUNTER
CTL
TC
UB
RESET
OPERATE/WARNING
MONITOR
SELECT
M
O
NITOR
CH-1
CH-2
AUDIO
LEVEL
E
REV FWD
FBATT
H
HM
MSF
REMAIN
AUD LOCK
32k
CH 1
CH 2
48k
PB NDF
AUTO OFF DEW
L iRFSERVO
HOLD
SP
MENU
OVER
OVER
40 30 20 10 0
dB
TC GENERATOR
FREE
REC
PRESET
REGEN
CH-1
CH-2CH-1
CH-2
CH-1 CH-2
CONTINUE MENU
PRESETADVANCESHIFTHOLD
AUTO
MANUAL
FRONT
REAR
DATA SET
SELECTITEMGROUP
AUDIO SELECT
AUDIO INPUT
AUDIO
LEVEL
LITHIUM BATT.
Lithium battery compartment
2.
COUNTER
switch
3.
HOLD
button
4.
SHIFT button
5.
PRESET button
4.
ADVANCE button
H M S
HOLD
H M S
HOLD
H M S
Time display (COUNTER switch: TC)
Hour Min. Sec.
HOLD
HOLD
Date display (COUNTER switch: UB)
Month Day Year
Check that the lithium battery has been inserted.
5-3 Setting the Date and Time
The date and time of the built-in clock should be set. During shooting, the date and time data are recorded in the sub-time code area
on the tape.
During playback, the data are shown on the counter display. Powered by the backup lithium battery, the set date and time data
continue to count even when the power is switched off.
1.
Turn ON the power and set the counter display to the date/
time mode.
Set the VCR Setup Menu item No. 516 DISPLAY SELECT
to “CLOCK”.
See “Displaying and Setting VCR Setup Menus” on
page 67.
See “VCR Setup Menu Contents” on page 69.
2.
Set the COUNTER switch to TC or UB.
To set the time: Set the switch to TC.
The time (Hour, Min., Sec.) is indicated on the counter
display. (24-hour clock system)
To set the date: Set the switch to UB.
The date (Month, Day, Year) is indicated on the counter
display.
3.
Press the HOLD button to enter the setting mode.
The “HOLD” indicator lights up on the display to indicate
that the unit is in the setting mode.
The leftmost digit on the counter blinks.
4.
Set the date and time.
Each time the ADVANCE button is pressed, the value of
the blinking digit increases.
Each time the SHIFT button is pressed, the digit to the
right of the currently blinking one starts blinking. When
pressed while the rightmost digit is blinking, the leftmost
digit starts blinking again.
Repeat the above procedure to set the value of all the
digits.
5.
To decide the set date and time data, press the PRESET
button.
The “HOLD” indicator on the display turns off and the date/
time display stops blinking.
The time starts counting.
To display and set the time code or user’s bit, set the VCR
Setup Menu item No. 516 DISPLAY SELECT to “TC”.
Memo:
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GY-DV500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GY-DV500 in the language / languages: English as an attachment in your email.

The manual is 4,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info