57093
37
Zoom out
Zoom in
Previous page
1/44
Next page
EN 37
TROUBLESHOOTING
MasterPage: Start_Right
REFERENCES
The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
Push the viewfinder back in or set “PRIORITY” to
“LCD”. ( pg. 17, 22, 24)
The LCD monitor’s brightness setting is too dark.
Adjust the brightness of the LCD monitor.
( pg. 16)
If the monitor is tilted upward 180 degrees, open
the monitor fully. ( pg. 17)
A malfunction of some kind has occurred. In this
case the camcorder’s functions become
unusable.
pg. 37.
Warning Indications
Displays the battery remaining power.
Remaining power level
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power
turns off automatically.
Appears if a tape is loaded.
Blinks when no tape is loaded. ( pg. 16)
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “REC”.
( pg. 14)
Appears if dirt is detected on the heads during
recording. Use an optional cleaning cassette.
( pg. 40)
Appears if condensation occurs. When this
indication is displayed, wait more than 1 hour
until condensation disappears.
Appears if a tape is not loaded when the
Recording Start/Stop Button or SNAPSHOT
Button is pressed while the Power Switch is set
to “REC”.
Appears when the tape ends during recording or
playback.
Appears when the date/time is not set.
( pg. 15)
The built-in clock battery has run out and the
previously set date/time has been erased.
Consult your nearest JVC dealer for
replacement.
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
Appears when pictures recorded in the HDV
format are detected. The pictures in the HDV
format cannot be played back with this
camcorder.
The error indications (01, 02 or 06) show what
type of malfunction has occurred. When an error
indication appears, the camcorder turns off
automatically. Remove the power supply
(battery, etc.) and wait a few minutes for the
indication to clear. When it does, you can
resume using the camcorder. If the indication
remains, consult your nearest JVC dealer.
The error indications (03 or 04) show what type
of malfunction has occurred. When an error
indication appears, the camcorder turns off
automatically. Eject the cassette once and re-
insert it, then check if the indication clears.
When it does, you can resume using the
camcorder. If the indication remains, consult
your nearest JVC dealer.
Picture does not appear on the LCD
monitor.
An error indication (01 – 04 or 06) appears.
CHECK TAPE’S ERASE PROTECTION TAB
USE CLEANING CASSETTE
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
ExhaustedHigh
TAPE!
TAPE END
SET DATE/TIME!
LENS CAP
HDV
UNIT IN SAFEGUARD MODE
REMOVE AND REATTACH BATTERY
OR DC PLUG
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
GR-D350AG_EN.book Page 37 Wednesday, December 28, 2005 8:24 AM
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D350AG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D350AG in the language / languages: English as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info