57093
36
Zoom out
Zoom in
Previous page
1/44
Next page
TROUBLESHOOTING
36 EN
MasterPage: Left
The light source or the subject does not include
white. Or there are various different light sources
behind the subject.
Find a white subject and compose your shot so
that it also appears in the frame. ( pg. 26)
Shooting was performed under backlit conditions.
Press BACKLIGHT. ( pg. 28)
The “Program AE” subject is too bright.
Set to “SPOTLIGHT”. ( pg. 31)
The Sepia (SEPIA) or Monotone (MONOTONE)
mode is activated.
Disengage the Sepia (SEPIA) or Monotone
(MONOTONE) mode before setting White
Balance. ( pg. 31)
When shooting in the dark, the unit becomes
highly sensitive to light when “GAIN UP” is set to
“AUTO”.
If you want the lighting to look more natural, set
“GAIN UP” to “AGC” or “OFF”. ( pg. 22, 23)
Other problems
Charging is difficult in places subject to extremely
high/low temperatures.
To protect the battery, it is recommended to
charge it in places with a temperature of 10°C to
35°C. ( pg. 39)
The battery pack is not attached firmly.
Detach the battery pack once again and re-attach
it firmly. ( pg. 12)
The date/time is not set.
Set the date/time. ( pg. 15)
The built-in clock battery has run out and the
previously set date/time has been erased.
Consult your nearest JVC dealer for replacement.
This is not a malfunction.
By recording with “DIS” de-activated
( pg. 22, 23) this can be avoided.
The DV cable was plugged/unplugged with power
turned on.
Turn the camcorder’s power off and on again,
then operate it.
In places subject to low temperature, images
become dark due to the characteristics of the
LCD monitor. This is not a malfunction.
Adjust the brightness and angle of the LCD
monitor. ( pg. 15, 17)
When the LCD monitor’s fluorescent light reaches
the end of its service life, images on the LCD
monitor become dark.
Consult your nearest JVC dealer.
The LCD monitor and the viewfinder are made
with high-precision technology. However, black
spots or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor or the
viewfinder. These spots are not recorded on the
tape. This is not due to any defect of the unit.
(Effective dots: more than 99.99 %)
The battery’s charge is low.
Install a fully charged battery. ( pg. 12)
The colour of Snapshot looks strange.
The image taken using Snapshot is too
dark.
The image taken using Snapshot is too
bright.
White Balance cannot be activated.
The image looks like the shutter speed is
too slow.
The POWER/CHARGE lamp on the
camcorder does not light during charging.
“SET DATE/TIME!” appears.
When the image is printed from the printer,
a black bar appears at the bottom of the
screen.
When the camcorder is connected via the
DV connector, the camcorder does not
operate.
Images on the LCD monitor appear dark or
whitish.
Coloured bright spots appear all over the
LCD monitor or the viewfinder.
The cassette will not load properly.
GR-D350AG_EN.book Page 36 Wednesday, December 28, 2005 8:24 AM
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC GR-D350AG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC GR-D350AG in the language / languages: English as an attachment in your email.

The manual is 2,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info