660748
20
Zoom out
Zoom in
Previous page
1/36
Next page
2020
External Control
About the external control
This monitor has two external control terminals.
l MAKE/TRIGGER terminal (RJ-45): The following external control
systems are available.
(1) MAKE (make contact) system:
Controls the monitor by short-circuiting the corresponding pin
terminal to the GND pin terminal, or disconnecting (opening) it.
(2) TRIGGER (trigger) system:
Controls the monitor by sending the pulse signal instantaneously
to the corresponding pin terminal.
+ “Using the MAKE/TRIGGER system”on the right
l RS-485 terminal (RJ-45): Controls the monitor with the RS-485
system. (+ “Using the serial communication” on page 21)
l RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-
232C system. (+ “Using the serial communication” on page 21)
Set the following items of “Remote Setting” in Set-Up Menu
according to the external control terminal and control system.
(+ “Serial Type,” “Parallel Type” on page 17)
Control
terminal
Control system
The settings of this unit
“Serial
Type”
setting
“Parallel
Type”
setting
MAKE/
TRIGGER
terminal
Parallel Type
MAKE Make
TRIGGER Trigger
RS-485
terminal
Serial
communication
RS-485 RS485*
1
RS-232C
terminal
RS-232C RS232C*
1
*
1
For a monitor connected to a personal computer etc, select the
terminal the equipment is actually connected to. For other monitors,
select “RS485.”
“MAKE” takes precedence over other controls.
l You can use external control even when “Control Lock” is set to
“Volume Lock” or “All Lock”. (+ page 17)
l When the monitor is off (on standby), external control is not
available. But certain external controls (starting/terminating
communication, turning on the monitor) are available through the
serial communication. (+ page 22)
<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated
controller*
2
.
l For the details, see “Using the MAKE/TRIGGER system” on the right.
*
2
The controller is not commercially available. Consult your dealer if
you need it.
<Serial communication>
PC, etc.
RS-485
IN
RS-485 IN
or
RS-232C
RS-485
OUT
RS-485
IN
RS-485
OUT
RS-485
OUT
l For the details, see page 21.
Using the MAKE/TRIGGER system
The MAKE/TRIGGER terminal is configured as follows.
You can assign a function to each pin terminal in “Remote Setting”.
(+ “Pin1, Pin2, Pin3, Pin4, Pin5” in “Parallel Type” on page 17)
l You cannot change the functions assigned to the pin terminals
from 6th to 8th.
Pin No. Pin name
1 Pin1
2 Pin2
3 Pin3
4 Pin4
5 Pin5
This is a female terminal. 6 Tally*
1
7 Enable*
2
8 GND
*
1
The 6th pin terminal controls turning on or off the tally lamp
(available to control even when the 7th pin terminal is invalid).
*
2
The 7th pin terminal makes the external control valid/invalid. Keep
the 7th pin short-circuited to 8th pin to make the external control
valid.
To assign the functions to the pin terminals
For the operation procedure, see page 9.
1 Select “Remote Setting” on the Set-Up Menu.
2 Set “Parallel Type” to “Set.”
3 Select a pin name (“Pin1” – “Pin5”) for which you want to assign a
function, then select the function you want to assign.
For the selectable functions, see the table on page 21.
Operation of the external control
1 Set “Parallel Type” of “Remote Setting” to “Make” or “Trigger” in the
Set-Up Menu.
2 Keep the 7th pin terminal (Enable) short-circuited to the 8th pin
terminal (GND) so that the monitor can be controlled by the external
control.
3 When the “MAKE” system is selected: Operate each function by short-
circuiting the corresponding pin terminal to the 8th pin terminal
(GND) or opening it.
When the “TRIGGER” system is selected: Operate each function by
pulse control, that is short-circuiting the corresponding pin terminal
to the 8th pin terminal (GND) for about 1 second and opening it.
l
When changing the input with MAKE system, activate the pin you
want after deactivating the currently used pin.
l When selecting the “TRIGGER” system, you can operate only one
function at a time. Operate the functions one by one.
DT-V24G2_EN.indb 20 2016/07/27 16:37:16
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JVC DT-V17G2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JVC DT-V17G2 in the language / languages: English as an attachment in your email.

The manual is 17,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of JVC DT-V17G2

JVC DT-V17G2 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info