656266
33
Zoom out
Zoom in
Previous page
1/41
Next page
PELLET BURNING STOVES
INSTALLATION AND MAINTENANCE MANUAL
33
ATTENTION!
Do not use abrasive products and do not spray the cleaning product on the glass of the painted parts or on
the gaskets of the fire door (ceramic fiber cord)
5.1.4.
Cleaning of stainless steel and satin-finish surfaces
Normally these surfaces do not need to be treated, but if they do, avoid cleaning them with abrasive materials. For
surfaces in stainless and satin brushed steel we recommend cleaning with a paper towel or a clean dry cloth moistened
with a detergent based on non-ionic surfactants (< 5%). A spray glass cleaner may be used.
5.1.5.
Cleaning of painted parts
Do not clean the painted parts with wet rags when the unit is in operation or hot to prevent thermal shock to the paint
which may cause it to detach. Do not use abrasive or aggressive products or materials. Clean with damp cotton or paper
towels.
The silicon paints used on HANKS products possess technical characteristics that make them resistant to
very high temperatures. There is however a physical limit (380°-400°) beyond which the paint begins to fade or (over
450°) to vitrify; it may then flake and detach from the steel surface. If this happens, it means that temperatures have
been
reached that are far above those at which the unit should
operate properly.
5.2.
CLEANING TO BE PERFORMED BY SPECIALIZED
TECHNICIAN
5.2.1.
Cleaning the heat exchanger and the pipe
unit
Halfway through the winter, but
especially in the spring
, you
will need to clean the compartment where discharge smoke
passes. This cleaning must be done in order to remove all
combustion residues before time and humidity let them harden
and make them difficult to remove.
5.2.1.1. CLEANING THE EXCHANGER AND PIPE
UNIT (EGO/STAR)
CLEANING THE UPPER COMPARTMENT
When the stove is cold, remove the top, remove the ceramics/
sides as described in section.3.3., loosening the relative
fastening screws before removing the drivers
“B”
and then
remove the boiler cover
“C”
. At this point, remove the
turbulators
“D”
and using a rigid rod or a bottle brush, clean
the internal pipe unit and the turbulators, removing all of the
accumulated ash. Check the cover gasket and replace it if
necessary.
ATTENTION:
It is advisable to carry out the cleaning of the upper
exchanger at the end of the season and possibly by an
authorised HANKS technician in order to replace the gasket that
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Just Fire NB-B18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Just Fire NB-B18 in the language / languages: English as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info