30210

JRpropo XP8103 Manual

77
Zoom out
Zoom in
Previous page
1/142
Next page
HELI 76
4.5 Travel Adjust (Function Mode)
4.6 Stunt Trim (Function Mode)
The Stunt Trim Function is a trim position setting for aileron,
elevator and rudder for use during forward flight maneuvers. This
function is activated when in the flight modes 1 and 2.
Note: When this function is activated, the trim levers of the
aileron, elevator and rudder are inactive. Maximum adjustment
range is approximately 30 degrees.
To adjust the stunt trim, fly your helicopter in a straight line at full
throttle/pitch in flight mode 1 or 2. Center the elevator stick.
Note which direction the helicopter pitches. If the helicopter
pitches up, land the model and add down stunt trim. Repeat
until no pitching occurs.
Next, check the rudder. Add rudder stunt trim until the tail tracks
directly behind the helicopter. Finally, adjust the aileron stunt trim
in the same manner until no rolling occurs. When properly
adjusted, your helicopter will fly straight and level at full speed
with no correction or trim required.
In Function Mode, use the UP and DN keys to select Stunt Trim
and access by pressing the UP and DN keys simultaneously.
Channel being programmed
THRO Throttle
AILE Aileron
ELEV Elevator
RUDD Rudder
GEAR Channel 5
PITCH Pitch/Aux 1
AUX2 Aux 2
AUX3 Aux 3
Initail setting
(inhibit)
Stunt Trim Value
(max
±
125)
Arrow indicates channel
to be adjusted
CLEAR
Press CLR key to reset value
(at arrow) to zero or to inhibit
stunt trim function
Press either + or - key to
activate and
Increase/Decrease value
Press the UP and DN keys
simultaneously to enter/exit
the Function Mode
Press the DN and Select keys
simultaneously to access the
Function Mode List Display
Press to increase or
decrease travel value;
move stick or switch to
manipualte arrow to the
position to be adjusted
(high/low, left/right)
Channel
Selection
Reset travel
value to factory
preset (100%)
DN
SELECT
CH CH CLEARUP
To Stunt Trim
function
To Sub-Trim
function
Press to display
channels 1-4 and
5-8 (2 screens)
The purpose of Travel Adjust, also known as endpoint
adjustment or adjustable travel volume, is to offer you precise
servo control deflection in either direction of servo operation.
The travel adjust range is from 0-150% (0 degrees to 60
degrees) from neutral and it can be adjusted for each direction
individually. The factory default (data reset) value is 100% for
each direction of servo travel.
In the Function Mode, use the UP or DN key to select the Travel
Adjust function and access by pressing the UP and DN keys
simultaneously.
… 77 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo XP8103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XP8103 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info