30210

JRpropo XP8103 Manual

33
Zoom out
Zoom in
Previous page
1/142
Next page
ACRO 32
CLR start transmitting
transmitting counter
(0-100%)
make sure that the receiving
mode transmitter (Tx to be
programmed) is in the stand-by
condition.
Transfer Procedure
1. Select the model number to be transferred (transmitting mode
side) through the model select function. (See page 28 for
information on Model Select Function.)
2. Both transmitters: With the power switches OFF, press the UP
and DN keys simultaneously while inserting the trainer cord into
the DSC jacks of both transmitters.
3. Both transmitters: Select the Transfer Fuction by pressing the
UP or DN key. Then simultaneously press the UP and DN keys to
enter the Transfer Function.
4. Receiving mode transmitter (Tx to be programmed): Press the
Select key until the screen reads "Receive." Select the receiving
model number by pressing the + or - keys. Next, press the CLR
key to activate the receiving stand-by mode.
5. Transmitting mode transmitter (Tx with program to be
transferred): Press the CLR key to start transmitting data. Both
transmitters will indicate [End ok!] display when the transmitting
is complete.
3.10 Data Transfer (System Set-Up Mode)
This function is used to transfer all existing memorized data for a
model from one XP8103 transmitter to another XP8103 transmitter.
Use the + and - keys to select models to be transferred and
activate by pressing the CLR key.
To avoid the loss of important data, re-confirm model names
when transferring.
Caution: Please use special caution when copy function is
activated as existing data is replaced with new data.
Caution: When the battery alarm is activated (battery low), the
copy function is not operational.
Transmitting mode
Model number
Display indicates DSC cord is
not connected, or Tx power
switch is on/off
Press + or -
keys to select
models to be
transferred
Press + or -
keys to select
the receiving
model number
DN
SELECT
CH CH CLEARUP
Press the UP and DN keys
simultaneously to enter/exit the
System Set-Up Mode
Press the DN and Select keys
simultaneously to access the
System Mode info display
To Wing Type
selection function
To Modulation
select function
Select
Transmitting/
Receiving Mode
Press to start
transmitting
data
DN
SELECT
CH CH CLEARUP
To Wing Type
selection function
To Modulation
select function
Transmitting/
Receiving Mode
select
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo XP8103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo XP8103 in the language / languages: English as an attachment in your email.

The manual is 2,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info