30201

JRpropo PCM10X Manual

10
Zoom out
Zoom in
Previous page
1/76
Next page
10
10X MANUAL Heli
It is extremely important that your radio system be correctly
installed in your model. Here are a few suggestions on the
installation of your
JR equipment:
1. Wrap the receiver in protective foam rubber that is no
less than 3/8 inch thick. Secure the foam to the receiver with
#64 rubber bands. This will protect the receiver in a crash or a
very hard landing.
2. The servos should be mounted using rubber grommets and
brass bushings to isolate them from vibrations. Do not over-
tighten the mounting screws — this will negate the vibration
absorption effect of the rubber grommets. The diagram at right
will assist you in properly mounting your servo.
The brass bushings are pushed from the bottom up in the rubber
grommets. When the servo screw is tightened securely, this will
provide the proper security as well as the proper vibration isola-
tion for your servo.
3. The servos must be able to move freely over their entire
range of travel. Make sure that the control linkages do not bind
or impede the movement of any of the servos.
4. Mount all switches away from the engine exhaust and
away from any high vibration areas. Make sure the switch oper-
ates freely and is able to operate over its full travel.
5. Mount the receiver antenna firmly to the helicopter to
ensure that it will not become entangled in the main and/or tail
rotor blades of your helicopter.
Connections
4
4.2
Connections
FM Rx
D72.550
BATT
AUX 5
AUX 4
AUX 3
AUX 2
AUX 1
GEAR
RUDD
ELEV
AILE
THRO
ON
OFF
Auxiliary 5
Auxiliary 4
Auxiliary 3/Gyro Gain
Auxiliary 2
Auxiliary 1/Pitch
Gear
Rudder
Elevator
Aileron
Throttle
NER-950S
S-PCM Receiver
Deluxe Switch Harness
JRPA001
Chargecord or
D.S.C. Receptacle
JRPA024
Chargecord or
D.S.C.
D.S.C. – JRPA123
Chgr. – JRPC222
Receiver Battery
1400mAh Sanyo Extra NiCad
JRPB4340
10 CH S-CLASS PCM RECEIVER
JAPAN REMOTE CONTROL CO., LTD
MADE IN JAPAN
ABC&W INTERFERENCE
PROTECTION SYSTEM
4.1
Installation Requirements
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRpropo PCM10X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRpropo PCM10X in the language / languages: English as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info