28352

JRC Radar1000_MKII Manual

21
Zoom out
Zoom in
Previous page
1/49
Next page
14
3.6 ELECTRICAL CONNECTION
3.6.1 DC POWER CABLE
The RADAR 1000 MK2 will work with any electrical supply within the 10.2
to 16 V range, since it contains a power regulator circuit. Connect the power
cable to a DC source capable of supplying at least 3 A. The power cable should
normally be wired through a circuit breaker. The red lead wire of the power
cable must be connected to the positive source terminal and the black lead to
the source negative terminal. The shielded wire is be connected to Boat Main
ground. Should the power connections be inadvertently reversed, a protective
fuse will blow. In this event, check the input power leads for correct polarity
with a VOM and reconnect the leads in their correct polarity. Replace the fuse.
The fuse is located in the power cable. [NORMAL-BROW FUSE (5 A)
SHOULD BE SPECIFIED]
3.6.2 EXTERNAL SYSTEM INTERFACE
The RADAR 1000 MK2 will interface with any NAV-AID (GPS or LORAN)
and compass with the standard NMEA0182 or NMEA0183 output. The inputs
from the NAV-AID must be digital data conforming to the NMEA0183 formats
to drive various radar features such as waypoint mode. If more than one data
type is present at the radar input (for example; compass and NAV-AID) a prior-
ity system has been established in the radar’s software to respond to the inputs
in driving the features. The assigned priorities are set in this manner:
HEADING: 1. Compass (NMEA0183 “HDG,HDM,HDT,VHW”)
2. NAV-AID (NMEA0183 “RMC,RMA,VTG”)
POSITION: 1. NAV-AID (NMEA0l83 “RMC,RMA,GLL,GTD”)
SPEED: 1. NAV-AID (NMEA0183 “RMC,RMA,VTG”)
2. Compass (NMEA0183 “VHW”)
WAYPOINT: 1. NAV-AID (NMEA0183 “RMB,BWC”)
Using the outline of FIG 3-7 as a guide, connect the RADAR 1000 MK2 to
your NAV-AID and compass.
INSTALLATION
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JRC Radar1000_MKII at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JRC Radar1000_MKII in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info