467790

Jotul F 474 Manual

18
Zoom out
Zoom in
Previous page
1/108
Next page
18
6.5 Exterior maintenance
Painted products may change colour after several years’ usage.
The surface should be cleaned and brushed free of any loose
particles before new paint is applied.
7.0 Servicing
Warning! Any unauthorised changes to the product are illegal!
Only original spare parts may be used!
7.1 Service/replacing parts in the burn
chamber
NB: Use tools with great care! The vermiculite plates may be
damaged if treated roughly.
Fig. 25
1. Lift the ash retainer (Fig. 25 A) up and out.
2. Slide or tap the lower exhaust deflector (Fig. 25 B) out of the
key hole (Fig. 25 C). Hold it while doing this so that it does
not fall down.
3. Pull the baffles (fig. 25 D) forwards, lift slightly, tilt and lower
them down.
4. Be sure to note the position of the exhaust deflectors (Fig. 25 E)
before removing them to ensure that they can be fitted back
into exactly the right places. Take hold of the pin (Fig. 25 F) on
the underside of the exhaust deflectors. Lift them up slightly
and then sideways before lowering them.
5. Lift the front side burn plates (Fig. 25 G) up and out.
6. Take hold of the upper part of the back side burn plates (Fig. 25 H)
and turn them in towards the middle of the burn chamber.
Then pull them out.
7. Pull out the back burn plate (Fig. 25 I). When fitting it back
into place, check that the gasket on the back burn plate is
securely attached.
8. Lift out the riddling grate (Fig. 25 J) (can be done first when
it needs replacing). Make sure that the slot on the riddling
grate is against the bar under the inner bottom plate when
it is fitted back into place.
9. Lift and move the inner bottom plate (Fig. 25 K) out.
10. Hold the upper air duct (Fig. 25 L) up at the front edge while
loosening the screw (Fig. 25 M). Use a ratchet with a 13 mm
socket and an extension piece. Tilt the air duct downwards
when the screw is loose. This can also be done after point 6.
There are gaskets at both the front and back of the air duct.
Glue new gaskets on before fitting it back into place.
11. When refitting, follow the same procedure in reverse order.
7.2 Replacing the side plates
Aluminium or glass sides
1. Undo the screws (Fig.15 A) holding the brackets on the top.
Lift the brackets up and remove the side plates. If the stove
has a smoke outlet on the top, the top plate can be raised and
turned to make it easier to get at the screws (A).
2. If necessary, insert new sides as described in Chapter 4.4.
Cast iron and soapstone side panels
1. Remove the screws (Fig. 6 A) that are underneath holding the
sides in place at the bottom.
2. Loosen the screws (Fig. 15 A) holding the sides on the top. Lift
off the sides. If the stove has a smoke outlet on the top, the
top plate can be raised and turned to make it easier to get
at the screws (A).
3. If necessary, insert new sides as described in Chapter 4.4.
7.3 Replacing glass and gaskets in the door
Fig. 26
1. Open the door and unhook the spring (Fig. 26 A) from the
clip (Fig. 26 B).
2. Lift the door off the hinges. Make sure that the washer under
the lower hinge (Fig. 26 C) does not get lost.
3. Place the door face down on a soft material.
ENGLISH
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jotul F 474 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jotul F 474 in the language / languages: English, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info