780425
3
Zoom out
Zoom in
Previous page
1/12
Next page
EN FR ES
• Bringtheseatbeltaroundthedoll’swaistandinsertthemaleendofeachwaiststrapbuckleintothefemalebuckle.Insurethattheysnap
into place. See Figure 5.3.Tightenthewaistbelttobesnugaroundthedoll’swaist.
Buckle the harness clip pieces together. See Figure 5.4.PositiontheharnessclipIthemiddleofthedollorstuffedtoy’schest,levelwith
the armpits and away from the neck.
Both the shoulder straps and the waist straps may be adjusted using the sliding buckle on these straps, located under the bottom of the
carrier. See Figure 5.5.
6 Using your Doll Car Seat in the Carrier Mode
To use the product in carrier mode, position the handle in the UP position as described previously.
The carrier may then be transported by holding on to the center of the handle and carrying it wherever your child goes.
!WARNING
NEVER use this toy to carry a baby or child for any purpose whatsoever.
DO NOT use as a carrier for any dolls or stuffed toys that weigh more than 4 lbs.
As with a real carrier, this toy carrier should never be placed near the edges of counter tops, tables, or other
elevated surfaces.
Using your Doll Car Seat in the Vehicle
7 Vehicle Seat Requirements
The doll car seat should be placed in the center position of the seat directly behind the front seat whenever possible.
Because a real car seat would not be placed in a vehicle location that has a front airbag, do not place this doll car seat in a similar
location.
The vehicle seat should always be a forward facing seat and the seat should lock in an upright position.
8 Installing the Doll Carrier and Base Using Vehicle Belts
To install the toy car seat in a vehicle, you must carefully follow the instructions provided by your vehicle manufacturer in addition to the
information in this manual. Before proceeding, be sure you have read and understand all of the instructions in this section.
Remove doll carrier from base. Place the base in a rear-facing position in the vehicle seat.
Thread the vehicle seat belt inside and through the curved plastic piece under the base. See Figure 8.1.
Buckle the vehicle seat belt, making sure the buckle tongue goes into the correct buckle. The vehicle belt should not be twisted. See
Figure 8.2.
Secure the base tightly into position by pushing down on the middle of the base with one knee or free hand while tightening the vehicle
belt.Refertoyourvehicleowner’smanualforinstructionstoproperlytightenthevehiclebelt.
Place the doll carrier in the base and make sure it “Clicks.” Pull up on the doll carrier to be sure it is latched securely in the base.
!WARNING
NEVER use this toy to hold a baby or child in a vehicle. Death or serious injury may occur.
DO NOT use as a car seat for any dolls or stuffed toys that weigh more than 4 lbs.
NEVER leave the car seat unsecured in a vehicle. An unsecured car seat can be thrown around and may injure you
or your child in a sharp turn, sudden stop, or crash.
DO NOT use this product if the carrier does not securely latch into the base. Contact Joovy Customer Service for
assistance.
9 Acceptable Vehicle Belt Systems
Thefollowingbeltsystemsareacceptableforusewithyourcarseat.Youshouldrefertoyourvehicleowner’smanualtodeterminewhich
type of seat belts your vehicle has.
Lap Belts-Manually Adjusted: When buckled, the belt is tightened manually by pulling on the excess belt while pushing down hard on the
car seat base.
Lap Belts with Automatic Locking Retractor (ALR): The automatic locking retractor will not allow the lap belt to lengthen once it is buckled.
Tighten the belt by feeding the belt back into the retractor while pushing down hard on the car seat base.
Combination Lap/Shoulder Belt with Locking Latch Plate: Once it is buckled, this type of belt has a latch plate that will not allow the lap
portion of the belt to loosen. Belt is tightened by pulling hard on the shoulder portion of the vehicle belt while pushing down hard on the car
seat base.
Combination Lap/Shoulder Belt with Sliding Latch Plate: This type of belt has a latch plate that slides freely along the belt. To prevent
movement of the lap portion of this type belt, the belt MUST be converted through the use of a Locking Clip, unless your vehicle belt can
beconvertedinanotherwayasdescribedinyourvehicleowner’smanual.
10 To install the locking Clip
Tighten the buckled belt by pushing down hard on the doll carrier and base and pulling hard on the shoulder belt.
While pushing down on the doll carrier and base, pinch the two straps together behind the buckle tongue. Unbuckle the belt without
allowing it to slip.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Joovy 003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Joovy 003 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info