509308
5
Zoom out
Zoom in
Previous page
1/44
Next page
POWER Amplifiers
3
Installation
Before you begin the installation of your Power series amp remember, there
are two ways to do things – right and twice! Use the proper installation
techniques, tools and accessories to ensure that your Jensen Power series
amp will put out all the power it was designed to. If necessary, seek a
professional installer to have the amplifier installed correctly. Most mobile amp
installations do not have the proper gauge wire for power and ground – do not
let your amp be a victim of this common installation oversight!
NOTE: This device is a high-power audio amplifier intended for
installation in vehicles with a 12-Volt negative ground electrical system.
Attempting to connect or operate the amplifier with another type of
electrical system may cause damage to the amplifier or the electrical
system.
Installation Assistance
For installation assistance, call 1-800-323-4815 during normal business hours,
or visit www.jensen.com at any time.
Supplies and Tools Needed
To install the amplifier, you will need tools, supplies and adapters. It is best to
make sure you have everything you need before you start.
Supplies
Black electrical tape
Amplifier Installation Kit
Tools
Cordless drill with assortment of bits
Flat-head and Philips screwdrivers
Wire cutters/strippers
Crimping tool
12-volt test light or digital multimeter
Wire brush, sandpaper or scraping tool (ground connection to vehicle should
be a clean, unpainted metal surface)
Disconnect Battery
Disconnect the negative (-) battery cable before starting the installation. Check
the battery ground (there should be two (2) ground wires coming from the
battery – one going to the starter mounting bolt or engine block and another
going to the vehicle chassis) and make sure the battery is grounded to the
chassis with at least a #8 gauge wire. Also check the alternator connections,
making sure they are tight and free from corrosion, rust or dirt.
Location and Mounting
The amplifiers compact design allows great flexibility in mounting. Common
mounting locations include under the front passenger seat or in the trunk area.
When selecting a location, remember that amplifiers generate heat. Select a
location on a flat surface away from heat and moisture where air can circulate
around the amplifier.
Place the amplifier in the mounting location and mark the positions of the holes
with a marker, pen or pencil. Carefully drill the mounting holes in the marked
positions, then use the supplied mounting screws to securely fasten the
amplifier to the mounting surface.
WARNING: Do not cover the amplifier with carpets or enclose it behind
interior trim panels, and do not mount the amplifier in an inverted or
upside down configuration. Be sure the mounting location and the
drilling of pilot holes will not damage any wires, control cables, fuel
lines, fuel tanks, hydraulic lines or other vehicle systems or components.
Routing Wires
Proper wiring connections are illustrated on the following pages. If wiring
connections are made incorrectly, the unit will not operate properly and could
become permanently damaged. Follow the installation instructions carefully, or
have the amplifier installed by an experienced technician.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jensen POWER 400.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jensen POWER 400.2 in the language / languages: English as an attachment in your email.

The manual is 1,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info