650510

JBL Cristalprofi e402 Manual

31
Zoom out
Zoom in
Previous page
1/243
Next page
27
9
Cleaning the hoses
Bacteria settle in the hoses producing slime, which can significantly obstruct the flow of
water. Algae growth only occurs in strong light. The hoses should therefore be cleaned reg-
ularly with a cleaning brush (e.g. JBL Cleany). Simply rinsing with tap water is not enough!
10
Cleaning the impeller and casing
Turn the cover of the impeller casing anti-clockwise towards “Open” and remove the cover
by pulling gently.
Pull the impeller out of the casing. CAUTION: the impeller is held in the casing by magnetic
force. Take appropriate care when removing the impeller, making sure to avoid injuring your
fingers.
The ceramic shaft is held by two rubber bearings, which remain either on the shaft or on
the bottom of the impeller casing, or in the middle of the casing cover, when the impeller is
removed.
Clean the impeller casing, impeller and shaft with a suitable cleaning brush, then rinse in
clean water. Limescale can be easily removed by soaking in JBL Clean A (available at your
specialist retailer). Never dip the pump head in water or other liquid to clean it. Use a damp
cloth (e.g. JBL WishWash) to clean the surface of the casing.
Place the ceramic shaft and impeller back in the casing. Check that both rubber bearings are
present and correctly positioned for the ceramic shaft. Put the impeller cover back in and,
pressing gently, turn the cover towards “CLOSE” until the stop point.
Please note: If the impeller has to be replaced due to wear and tear, the complete set com-
prising the impeller with the shaft and 2 rubber bearings must be replaced. Only this way
can flawless operation and quiet running be guaranteed. When the impeller and shaft are
removed, a rubber bearing often adheres to the base of the impeller casing where it is very
difficult to remove. JBL has produced a special tool for this purpose which is available at
specialist pet shops under the name “Extraction tool for impeller bearing”. A useful clean-
ing brush for the impeller casing comes with the tool.
11
Re-starting the filter
Place the pump head back on the filter canister and close the locking clips as described in
(1). Place the hose connection block with the attached hoses back in position as described
in (2). Then turn the right-hand stopcock lever towards “OPEN” until the stop point. Repeat
with the left-hand lever a few seconds later.
If the water does not begin to run into the filter automatically, start the filter as described
in (5).
Connect the filter to the mains power supply.
de
en
fr
nl
it
sv
es
pt
pl
cs
ru
ro
tr
el
zh
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Cristalprofi e402 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Cristalprofi e402 in the language / languages: All languages as an attachment in your email.

The manual is 4,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info