809548
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
SpEAkER CONNECtIONS
DOLBy® DIgItAL OR DtS® (OR OthER DIgItAL SURROUND MODE) CONNECtION
Use this installation method for Dolby Digital, DTS or other digital surround processors:
LINE
LEVEL
IN
LFE
L
R
LFE OUT
RECEIVER SUBWOOFER
Use the line-level input jack marked “LFE” for the Low-Frequency Effects channel. Connect this jack to the LFE output
or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on
your receiver or amplifier.
Make sure that you have configured your surround-sound processor for “Subwoofer On.” Also, configure your receiver
for 5.1-, 6.1- or 7.1-channel operation as appropriate. The front left, front right, center and back speakers should
all be set to “Small.” If your receiver allows you to set the crossover frequency between the subwoofer and the main
speakers, select 100Hz or the setting that is the closest frequency below it.
DOLBY PRO LOGIC® (NON-DIGITAL) – LINE LEVEL
Use this installation method for Dolby Pro Logic® applications (not Dolby Digital, DTS or other digital processing),
where the receiver/processor is equipped with a subwoofer output or a volume-controlled preamp (line-) level output:
– +
+– +
– + – +
– +
– +
– +– +
Left
Surround
Left
Front
Right
Front
Center Front Right
Surround Right
Subwoofer
Receiver
Subwoofer
Out
Line
Level In
L
Front Left
Surround Back
Left
Surround Back
Right
Surround Back
Left Right
Surround
Center
Surround Back
Right
– +
Surround Left
– +
– +
– +
– +
R
RL
Use RCA-type cables to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs
on the subwoofer. IMPORTANT: Do not use the LFE input on the subwoofer with Dolby Pro Logic processors.
NOTE: If your receiver or amplifier has only one subwoofer output jack, then you will need to use a Y-connector (not
included). Plug the male end of the Y-connector into your receiver or amplifier’s subwoofer output jack, and connect
each of the two female ends to separate RCA-type interconnects. Finally, plug the RCA-type interconnects into the
line-level inputs on the subwoofer.
Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure your receiver or
processor is correctly configured to indicate that the subwoofer is “On.”
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL CINEMA SOUND CSB6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL CINEMA SOUND CSB6 in the language / languages: English as an attachment in your email.

The manual is 1.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info