810183

JBL AVR480 Manual

6
Zoom out
Zoom in
Previous page
1/52
Next page
6
1
Main Power Switch
2
System Power Control
3
Power Indicator
4
Headphone Jack
5
Remote Sensor Window
6
Tone Mode Button
7
Surround Mode Selector
8
Tuning Selector
9
Tuner Band Selector
)
Preset Stations Selector
!
Input Source Selector
@
Tuning Mode Selector
#
Video 3 Input Jacks
$
Volume Control
%
‹/›Selector Buttons
^Set Button
&Delay Button
*Digital Input Selector
(
Main Information Display
ÓChannel Select Button
Ô
Speaker Select Button
Test Tone Selector
1
Main Power Switch: Press this
button to apply power to the AVR480.
When the switch is pressed in, the unit
is placed in a Standby mode, as indicated
by the red LED Power Indicator
3
in the middle of the System Power
Control
2
. This button MUST be
pressed in to operate the unit. To turn
the unit off completely and prevent the
use of the remote control, this switch
should be pressed until it pops out from
the front panel so that “OFF” may be
read at the top of the switch.
NOTE: This switch is normally left in the
“ON” position.
2
System Power Control: When the
Main Power Switch
1
is “ON,” press
this button to turn on the AVR480; press
it again to turn the unit off (to Standby).
Note that the Power Indicator
3
inside the switch will turn orange when
the unit is on.
3
Power Indicator: This LED will be
illuminated in red when the unit is in the
Standby mode to signal that the unit is
ready to be turned on. When the unit is in
operation, the indicator will turn orange.
4
Headphone Jack: This jack may be
used to listen to the AVR480’s output
through a pair of headphones. Be certain
that the headphones have a standard
6.3mm (1/4-inch) stereo phone plug. Note
that the speakers will automatically be
turned off when the headphones are
connected.
5
Remote Sensor Window: The sen-
sor behind this window receives infrared
signals from the remote control. Aim the
remote at this area and do not block or
cover it unless an external remote sensor
is installed.
6
Tone Mode Button: Pressing this
button activates the menu for setting the
Bass and Treble controls.
7
Surround Mode Selector: Press this
button to change the surround mode by
scrolling through the list of available
modes. Note that Dolby Digital and DTS
modes can be selected only when a digi-
tal input is used (see page 28 for more
information about surround modes).
8
Tuning Selector: Press the left side
of the button to tune lower-frequency
stations and the right side of the button
to tune higher-frequency stations. When
a station with a strong signal is reached,
the TUNED Indicator
J
will light in
the Main Information Display
(
(see
page 31 for more information on tuning
stations).
FRONT-PANEL CONTROLS
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL AVR480 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL AVR480 in the language / languages: English as an attachment in your email.

The manual is 0.86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info