602026

Janome Memory Craft 4800 Manual

25
Zoom out
Zoom in
Previous page
1/68
Next page
24
Practice Common Stitching Skills
Using the Seam Guides on the Needle Plate
The seam guides on the needle plate are engraved to help
you measure seam width.
The lines are marked as follows.
* The numbers indicate the width from the center needle
position to the edge of the fabric.
1
Needle drop position
2 Edge of fabric
1 Guide lines
Turning Square Corners
Turning a square corner 1.5 cm (5/8 “) from the fabric edge:
1. Stop stitching and lower the needle by pressing the
Up/down needle position button when the fabric edge
facing you lines up with the cornering guides as shown.
2. Raise the presser foot and turn the fabric to line up to
the edge with the 1.5 cm (5/8”) seam guide.
3. Lower the presser foot and begin stitching in the new
direction.
1 Up/down needle button
2 Cornering guides
3 Presser bar lifter
Using the Quilting Bar
The stitch and its uses:
Quilting is stitching two layers of fabric together with batting
in between to add dimension and warmth.
You can use quilting on entire garments or parts of garments,
such as yokes, pockets, cuffs and collars.
It is also popular for table fashions.
In addition to straight stitch quilting, you can quilt with deco-
rative stitches or stitch pattern combinations.
To do quilting successfully, follow these simple steps:
1. Loosen the quilter screw 1 on the back of the presser
foot holder as shown.
2. Slide the quilting bar w into the opening under the
screw to the width of quilting stitches you desire.
3. Tighten screw.
4. See page 47 for how to operate.
1 Screw
2 Quilter bar
3 Measurement lines
Sewing on Heavy Fabrics
The black button on foot A will lock the foot in a horizontal
position if you push it in before lowering the presser foot.
This ensures even feeding at the beginning of seams and
helps when sewing many layers of fabric such as sewing
over welt seams when hemming jeans.
When you reach the point of an increased thickness, lower
the needle and raise the presser foot. Press the toe of the
foot and push in the black button, then lower the foot and
continue sewing.
This button releases automatically after a few stitches.
Note: When sewing an edge, select stitch pattern 02.
1 Fabric
2 Black button
Numbers on needle plate
Seam width center needle
position guide line (cm)
15 20 4/8” 5/8” 6/8”
1.5 2.0 1.3 1.6 1.9
1
2
3
2
3
1
1
2
3
1
2
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome Memory Craft 4800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome Memory Craft 4800 in the language / languages: English as an attachment in your email.

The manual is 2,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info