472843

Janome Jem Gold 3 Manual

40
Zoom out
Zoom in
Previous page
1/52
Next page
40
qw e
r
t
y
u
z
xc v
b
n
m
Buttonhole
Machine setting:
q Stitch selector:
w Presser foot: Buttonhole foot
e Thread tension dial: 1-5
* Before you sew the actual buttonholes on the
actual garment, make several trial buttonholes on
a fabric sample.
* Use interfacing on stretch fabrics.
z Select BH 1( ). Pull the slider so the top mark on
the slider aligns with the start mark. Draw both
threads to the left under the foot.
Insert the garment under the foot.
r Start mark
x Lower the needle at the starting point. Then lower the
buttonhole foot.
Sew the required length of the left side of the button-
hole and stop the machine.
c Raise the needle to its highest position by turning
the handwheel, then select the BH 2,4( ).
Sew five bartack stitches and stop the machine.
v Raise the needle to its highest position and select
BH 3( ), sew the right side of buttonhole the
same length as the left side and stop the machine.
b Raise the needle and select the BH 2,4( ), and
sew five bartack stitches.
n Raise the needle and presser foot. Remove the fabric
from the machine. Cut both needle and bobbin
threads leaving approximately 10 cm (4˝) of thread
ends loose.
Draw the needle thread to the wrong side of the
fabric by pulling the bobbin thread. Then, knot the
threads.
m Place a pin just before the bartack to prevent cutting
bartack. Cut the opening with the seam ripper.
t Seam ripper
Corded buttonhole
1. With the buttonhole foot raised, hook the filler
cord on the spur y at the back of the buttonhole
foot. Bring the ends toward you under the
buttonhole foot, clearing the front end.
Hook the filler cord into the forks u on the front of
the buttonhole foot to hold them tight. Lower the
needle into the garment where the buttonhole
will start and lower the foot.
y Spur
u Forks
2. Depress the foot control and sew the buttonhole over
the filler cord in the same way as described above.
3. Pull the left end of the filler cord to tighten it.
Thread the end of the cord through a darning
needle, draw it to the wrong side of the fabric and
cut.
… 40 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome Jem Gold 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome Jem Gold 3 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info