733898

Janome HD9 Manual

24
Zoom out
Zoom in
Previous page
1/52
Next page
20
Threading the Needle Thread (Leather, heavy weight fabric)
c
y
t
u
v b
t
i
i
!1
o
!1
!2
!2
!3
!4
w
e
r
!0
!0
(A)
x
z
q
!3
!4
Pre-tension dial
The screw should be lower
than the pre-tension dial.
Higher than the pre-tension dial.
Holding the thread
with both hands.
Insert thread
between the
tension disks.
No gap with the pre-tension dial.
Correct
Wrong
Wrong
Loosen the adjusting screw with the screwdriver provided with the machine.
Slide the adjusting plate to the right or left to adjust the needle thread
tension. Tighten the adjusting screw. Normally adjust the needle thread
WHQVLRQE\WKHWKUHDGWHQVLRQGLDOUHIHUWR´$GMXVWLQJ1HHGOH7KUHDG7HQVLRQµ
on page 34).
Synthetic thread size 20 to 30 is recommended.Do not
XVHWKUHDGVL]HRUÀQHU2WKHUZLVHWKUHDGPD\EUHDN
Adjusting plate
Loose
Needle thread
tension
Tight
Adjusting screw
* Adjusting the needle thread tension by the thread guide
o
.
* Use only left twist thread.The left twist
WKUHDGZLOOWZLVWÀUPO\ZKHQ\RXWZLVW
LWWRZDUG\RXZLWKÀQJHUVRI\RXUULJKW
hand.
Screw
n
z
Raise the presser foot lifter. Press the Up/Down
needle button twice to raise the needle to its
highest position. Turn the power switch off.
Set a spool of thread on the spool pin.
Pass the thread through the guide on the thread
guide bar
q
from the behind.
x
Pass the thread through the thread guide plate
w
,
then draw the thread between the pre-tension
disks
e
under the pre-tension dial
r
.
* If the thread tends to twist too much, pass the
thread through the 3 holes in the thread guide
SODWHDVVKRZQLQWKHÀJXUH$
* The standard setting of the pre-tension dial is
WKDWWKHVFUHZKHDGVLQNVDERXWPPßWR
ß
c
Holding the thread with both hands, draw the
thread down and around the tension dial
t
from
right to left.
Pull the thread up to insert it between the tension
disks
y
and pass it over the tail of the check
spring
u
. Then pull the thread down over the
loop of the check spring.
v
Draw the thread under the thread guide
i
.
Pass the thread through the 2 holes in the thread
guide
o
as shown.
* The needle thread tension can be adjusted by
the thread guide
o
.
b
Through the eye of the take-up lever
!0
.
Pass the thread through the thread guide
!1
.
Holding the thread with both hands, slip the
thread into the thread guide
!2
as shown.
n
Draw the thread down to the needle bar thread
guide
!3
, and then pass the thread through the
needle eye on the left side of the needle
!4
.
o
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome HD9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome HD9 in the language / languages: English, French, Italian as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info