641102

Janome DC2030 - JNH1860 Manual

43
Zoom out
Zoom in
Previous page
1/44
Next page
Troubleshooting
Condition
The needle thread
breaks.
The bobbin thread
breaks.
The needle breaks.
Skipped stitches
Seam puckering
The cloth is not
feeding smoothly.
Stitches form loops
below the works.
The machine does not
work.
Buttonhole sewing is
not sewn properly.
The machine does not
run smoothly and is
noisy.
1. The needle thread is not threaded properly.
2. The needle thread tension is too tight.
3. The needle is bent or blunt.
4. The needle is incorrectly inserted.
5. The needle thread and the bobbin thread are not set under the
presser foot when start sewing.
6. The threads were not drawn to the rear after sewing.
7. The thread is either too heavy or too fine for the needle.
1. The bobbin thread is not threaded properly in the bobbin holder.
2. Lint has collected in the bobbin holder.
3. The bobbin is damaged and doesn’t turn smoothly.
4. The thread is wound loosely on a bobbin.
1. The needle is incorrectly inserted.
2. The needle clamp screw is loose.
3. The threads were not drawn to the rear after sewing.
4. The needle is too fine for the fabric being used.
5. The presser foot is not appropriate for the stitch pattern being sewn.
1. The needle is incorrectly inserted, bent or blunt.
2. The needle and/or threads are not suitable for the work being sewn.
3. A Blue Tipped needle is not being used for sewing stretch, very fine
fabrics and synthetics.
4. The needle thread is not threaded properly.
5. A poor quality needle is used.
1. The needle thread tension is too tight.
2. The needle thread is not threaded properly.
3. The needle is too heavy for the fabric being sewn.
4. The stitch length is too long for the fabric.
1. The feed dog is packed with lint.
2. The stitches are too fine.
3. The feed dog is not raised after “drop feed” sewing.
1. The needle thread tension is too loose.
2. The needle is either too heavy or too fine for the thread.
1. The machine is not plugged in.
2. Thread has been caught in the hook race.
3. The bobbin winder spindle is not returned to the left after bobbin
winding.
1. The stitch density is not suitable for the fabric being sewn.
2. Suitable interface material has not been used for the stretch or
synthetic fabric.
1. Thread has been caught in the hook race.
2. Lint has built up in the hook race or bobbin holder.
Reference
See page 13, 14
See page 17, 18
See page 9
See page 9
See page 19
See page 19
See page 9
See page 12
See page 39
Replace the bobbin.
See page 11
See page 9
See page 9
See page 19
See page 9
Change the presser foot.
See page 9
See page 9
See page 9
See page 13, 14
Change the needle.
See page 17, 18
See page 13
See page 9
Make the stitches shorter.
See page 39
Make the stitches longer.
See page 9
See page 17, 18
See page 9
See page 4
See page 39
See page 11
See page 28
Use an interfacing.
See page 39
See page 39
Cause
41
… 43


Need help? Post your question in this forum.

Forumrules
1

Forum

janome-dc2030---jnh1860

Reset search

  • Are the Janome JNH1860 AND THE JNH2030 the same machine? Submitted on 23-1-2023 at 21:57

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome DC2030 - JNH1860 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome DC2030 - JNH1860 in the language / languages: English as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info