554896
4
Zoom out
Zoom in
Previous page
1/12
Next page
Telephone dialer TD-101 / TD-101W - 4 - MDJ512 10 Telephone dialer TD-101 / TD-101W - 21 - MDJ512 10
3. TD-101 includes
the dialer, 2.5m telephone cable, set of screws, manual, and
emergency
F button marking label. Model TD-101W, in
addition, includes a wireless remote control (RC-10)
4. Installation
We recommend professional installation of the dialer. The
dialer should be fixed in the desired location using the two
included screws (see drilling diagram at the end of this manual).
First, partially screw in the top screw and slide the screw head
through the hole in the upper part of the TD-101 rear panel. Then
open the dialer terminal compartment cover and mark the position
of the second screw. Place cables through the hole for cables in
the rear panel before installing the second screw. Do not open the
upper part of TD-101 housing during installation; doing so will
result in voiding of warranty.
4.1. Terminal Description
IN telephone line input (inlet of the telephone line to
the house)
OUT telephone line output (phone, fax etc.); in the stand by mode the line operates as normal. If
triggered, the TD-101 will use the line (switch off the other devices)
+12V, GND external power supply (12VDC, max. 100mA)
TAMPER tamper switch (normally closed contacts)
IN1 +/- positive and negative poles of the first trigger input
IN2 +/- positive and negative poles of the second trigger input
Both TD-101 trigger inputs have built in opto-
couplers. The dialer is triggered when an opto-
coupler current is switched on (factory default),
opposite logic of inputs is programmable (trigge-
ring by the current switching off). There are
many possibilities on how to connect the trigger
inputs - see examples on page 20. Consider
that the dialer reacts only to signals with a
duration of 0.1sec. or longer. Each optocoupler
is ON only if its input terminal voltage is 5 to
20V.
5. Operation
When power is supplied, the dialer will perform an automatic self test (red LED turns on for
10 seconds). Then the TD-101 will enter the stand by mode. In this mode, the TD-101 is waiting for an
input form either the keypad or the trigger inputs. For correct function of the dialer, the telephone
numbers and messages must first be programmed (see chapter 6.).
5.1. What does the dialer do if activated:
seizes the telephone line (switches off all other devices)
checks dial tone, if the tone is not detected, it will try to release the line again
dial the first tel. number and if detects:
ringing tone, it will send the message and will not call this number again
busy signal, it will call next number and then will try to call the previous number again
The red LED will light when the dialer has been triggered. Once the dialer has been triggered, it's dialing
procedure can be terminated by pressing and holding the
E key (if enabled in installer level). This is
possible only when the IN1 and IN2 inputs are not triggered.
11.3. Example of TD-101(W) use with different alarm systems
Suggestion of programming for the configuration above
tel. number memories
Mem
1, 2 - not used
user mode
3, 4 - numbers for alarm voice message
setting
5 - not used
6 - alarm PAGER number and data
record only voice mess. no. 2
data for Monitoring Station
four report codes disarming
installer
mode
can be programmed arming
setting
(see chapter 8) alarm
end of alarm
logic of IN1 and IN2 inputs Normally Closed contacts
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron TD-101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron TD-101 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info