The JA-82Y GSM communicator installers manual 12/12 MDL51108
•
13. Communicator programming sequence overview
Sequences beginning with “8“ are also accessible from Maintenance mode if the change of telephone numbers in Maintenance mode is enabled (OASiS control panel sequence
251)
Function Sequence Possible options Factory default settings
Communicator language setting 991 xx
xx=01 to 18
Language selection affects SMS texts and basic
voice menu features
English
GSM signal strength measuring 888 range 1/4 to 4/4, exit by pressing # -
Tel. number programming for reporting to
telephones
81 M xx..x ∗0
M = memory 1 to 8; 0 is for the own SIM card
number;
xx..x = tel. number (max.20 digits)
keying in *9 inserts +, keying in *7 inserts * ,
81 M *0 erases the number in memory M
- remote control by unanswered calls – see 3.4
all M1 to M8 erased
Selection of events to report by SMS 82 M uu x
M = tel. number memory 1 to 8
uu = event code, see the 3.4
x=1 report, x=0 no report
in a split system, alarm reports are defined for
sections A, B, or ABC
M1 alarms and faults from sections A, B, C by SMS.
M2 and M3 Alarms from sections A, C by SMS and
phone calls
M5 and M6 alarms from sections B, C by SMS and
phone calls
M4 alarms from A, C and M7 alarms from B, C by
SMS
M8 faults only by SMS from A, B, C sections
Selection of events to report by phone call 83 M uu x
See the List of events which can be reported to
your phone and their factory default settings
Codes associated with enrolled telephones84 M xxxx
If a codeless SMS arrives from telephone number
M, xxxx is used as a code, keying in 84 M *0 erases
the given code
No code
Allowing remote access from telephone
numbers
85 M x
Allow remote access by authorized numbers M1 –
M8,
x=1 allow, x=2 deny
allow
SMS and instruction text editing
The texts can be changed by OLink software or by sending an instructional
SMS: code TXT n,text,n,text...
See 6.8
Voice message recording
The recording is performed via a mobile phone; the system must be in service or user mode. Dial the system SIM card number from
your telephone. When the system answers, key in the SC, MC, UC code and then key in 892. The communicator will announce:
“You are in voice message recording mode, see the installation manual.“ see 6.9
Enable reporting to phones 901 x
x=0 disabled
x=1 enabled (all programmed)
x=2 enabled without reporting setting/unsetting
by users 41 to 50 (codes, cards & key-fobs) and
master code setting/unsetting
enabled
Enabling remote access 802 x
x=0 no
x=1 yes (by phone and Internet)
x=2 yes, but only by enrolled phones
1=yes
Forwarding of incoming SMS messages 801 x
x=0 no, x=1 if the incoming text is not an SMS
instruction it will be forwarded to the first
programmed number in memories M1 to M8
yes
Autoconfiguration of GPRS 903 x
X=0 autoconfiguration disabled
x=1 autoconfiguration enabled
Autoconfiguration enabled
SMS instruction confirmation 904 x x=0 no, x=1 yes (by SMS reply) yes
Reaction to incoming calls 905 x
x=0 no reaction
x=1 answers after 15s ringing
answers after ringing for 15s
GSM signal dropout indication 906 x x=0 no, x=1 yes (15min. dropout =fault) no
Time synchronization via SMS 907 x X=0 off, x=1 synchronization on on
Phone speaker loudness 909 x x=0..9, 0=minimum,9=maximum 5
Number to be called to maintain SIM card
validity
910 xx..x*0
xx..x = tel. number (max.20 digits), 910*0 erase the
number
Erased
Restriction of the number of sent SMS to
max. 50 SMS per 24 hours
803 x 1=restriction enabled, 0=restriction disabled restriction enabled
SIM card credit interrogation
You can inquire about credit balance by sending the SMS instruction: code CREDIT uu..u xx yyy zz where code = master or
service code, uu..u = GSM network command string to ascertain the credit (e.g. ∗104#), xx=auto-interrogation frequency in days,
yyy=minimum acceptable balance, zz= the textual position at which the number showing the balance starts in the reply message
from the GSM provider. If the credit is lower than the set minimum value, the provider’s SMS will be auto-forwarded to numbers M1
and M8 for someone to top up the pre-paid SIM card
Programming by SMS
The system can be programmed remotely via SMS instruction code PRG seq, seq,... where seq are programming sequences set
in the same way as from the keypad (e.g. 8080 PRG*08080 201 # sets the 10s exit delay
(a space in the sequence causes a 500ms pause)
Registration code
911 xx...x ∗0
xx..x = tel. number to which the registration code
should be sent
Re-registration to the GSM network 893
the communicator disconnects from the GSM network and then re-registers itself, this function can also b
e
performed by SMS: code GSM
Communicator reset 998080 Resets to the factory default settings and erases all phone numbers, text will not be changed
SIM card’s PIN code
920 xx..x ∗0
xx..x = PIN, 920*0 erases the PIN (to use a SIM
card with a disabled PIN)
erased
GPRS parameter settings
by SMS instruction: code GPRS apn user pass where apn = APN, user = username, pass = password (only enter the APN if the
name and password are not required by the GSM provider)
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Jablotron JA-82Y GSM communicator at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Jablotron JA-82Y GSM communicator in the language / languages: English as an attachment in your email.
The manual is 0,22 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
Others manual(s) of Jablotron JA-82Y GSM communicator
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
