631258
4
Zoom out
Zoom in
Previous page
1/13
Next page
The JA-82Y GSM communicator installers manual 4/4 MDL51108
6.10. Quick enabling / disabling of reporting to phones
Event reports to your phone can be enabled / disabled as follows:
901 0 all SMS and call reports disabled
901 1 all SMS and call reports enabled
901 2 all reports enabled except reports of setting and unsetting by
users 41 to 50 (i.e. their codes, cards and key fobs). Master code
control is not reported either. This allows setting and unsetting done by
report recipients (owners, bosses, etc.) not to be reported.
Factory default setting: 9011 all reports enabled
6.11. Enabling remote access
The following sequence enables remote access to the system by phone or
Internet:
802 0 remote access completely disabled
802 1 access from any telephone and Internet access via OLink enabled
802 2 access from programmed phones and Internet access via OLink
enabled
Factory default setting: Remote access enabled
6.12. Forwarding of incoming SMS messages
The communicator enables the automatic forwarding of incoming SMS messages
which contain no valid instructions to the system:
801 0 messages are not forwarded, but the communicator saves the last
10 received messages to the SIM card
801 1 messages are forwarded to the first programmed tel. number in
memories M1 to M8 (e.g. if numbers are only programmed in M5
and M6, then messages will be forwarded to M5). The tel. number
from which the SMS was received will be shown at the beginning of the
forwarded text.
Factory default setting: messages are forwarded
Note:
In order to protect the user against runaway (donation SMSes etc.), the
forwarding is limited to the first 50 SMS messages. The counter can be erased
automatically each midnight, by processing any SMS instruction or by exiting
Service / Maintenance mode.
6.13. Automatic GPRS configuration
If the communicator detects a SIM card change and the main power is on, it sends
an SMS to the YTUN Jablotron server with the network identification. The server
sends back : APN, login, password and own SIM card telephone number.
903 0 auto configuration disabled
903 1 auto configuration enabled
Factory default setting: auto configuration enabled
6.14. SMS instruction confirmation
If the communicator receives a valid SMS instruction, a confirmation SMS will be
sent a s a reply. This confirmation can be disabled as follows:
904 0 disabled
904 1 enabled
Factory default setting: enabled
6.15. Reaction to incoming calls
This sequence can be used to set the communicator’s reaction to incoming phone
calls:
905 0 the communicator ignores incoming calls
905 1 the communicator will answer after ringing for 15s
Factory default setting: answer after ringing for 15s
6.16. GSM signal dropout indication
This feature enables the monitoring of GSM network signal availability. If enabled
and if there is a GSM signal dropout longer than 15 minutes, the control panel
announces “External communication fault”.
906 0 signal availability monitoring disabled
906 1 signal availability monitoring enabled
Factory default setting: disabled
6.17. Time synchronization via SMS
This setting enables the function for synchronizing the clock in the control panel.
See chapter 8.5 for further details.
907 0 synchronization off
907 1 synchronization on
Factory default settings: on
6.18. Phone receiver loudness
To set the loudness of the receiver of the phone which is used to call the
communicator key in:
909 x where x is a number from 1 to 9 (max.)
Factory default setting: 9 (max.)
6.19. Number to be called to maintain SIM card validity
If a prepaid SIM card is used and a lack of outgoing phone calls for a certain period
cancels the validity of the SIM card, then this function offers the following: if there
have been no outgoing phone calls within the last 90 days, then the communicator
automatically calls the number programmed by this sequence. The communicator
waits until the call is answered and then automatically hangs up after 10 sec.
910 xx...x 0
where: xx...x is the telephone number
Notes:
To erase this number enter 910 *0
It is recommended to call cheap public services (e.g. weather forecasts etc.)
but not toll-free numbers.
Factory default setting: Erased
6.20. Restriction of the number of sent SMSes
The parameter limits the amount of sent SMSes to 100 per 24 hours. 50 may be
alarm SMSes and 50 may be for other events. This is to prevent enormously high
telephone fees.
803 0 restriction disabled
803 1 restriction enabled
Factory default setting: enabled
6.21. Prepaid SIM card credit interrogation
The communicator is capable of checking the credit balance of its SIM card upon
request (by “CREDIT” SMS instruction) or this activity can be requested
automatically (with a preset cycle) and if it finds out that the remaining credit is
lower than the preset value, an information SMS is sent. The function is set by
sending the following SMS instruction:
code_CREDIT_uu..u_xx_yyy_zz
where:
Code valid access or service system code (e.g. 8080 or 1234), the change of
parameters is possible on with a service code (other codes allow SMS credit
interrogation “1234 CREDIT“)
_ space
uu..u instruction recognized by the GSM network to check the balance
xx automatic checking period in days,
yyy minimum acceptable credit balance
zz the textual position in which the number showing the balance starts in
the reply message from the GSM provider.
Notes:
If the reported credit balance is lower than the set limit (yyy), text no. 545 will be
sent to phone numbers M1 and M8 which have the “Low credit balance” (event
no. 50) event sending enabled
If only uu..u follows the CREDIT instruction (no xx yyy zz) then periodic balance
checking will not be performed, but the balance will be checked immediately
If there is further data following the CREDIT instruction, the communicator will
memorize them and automatically put them in the message when the CREDIT
instruction is used again (i.e. the Credit instruction must contain at least the
uu..u part upon the first sending) and the user just needs to send: code
CREDIT
Example: sending the SMS instruction “code CREDIT
101# 7 50 1” causes the
credit balance to be checked every 7th day after the SMS has been sent and if the
balance (starting with the first character in the message from the GSM provider) is
lower than 50 currency units it will be reported.
Warning: the use of prepaid SIM cards in the communicator can negatively
influence the reliability of the device. Some GSM providers block cards not
only when there is no credit but also when they are not topped up frequently
enough. This means that even if there is enough credit balance on the card,
the communication can still be blocked. We therefore strongly advise the
use of tariff SIM cards !!!
6.22. Remote programming by SMS instructions
The communicator enables remote programming of the system by the following
SMS instruction:
code_PRG_seq_seq, another instruction
where:
Code valid access or service system code (e.g. 8080 or 1234)
_ space
seq programming sequence usually set via the keypad
Notes:
Only characters which can be keyed in from the system keypad (0 to 9, * and
#) can be used in the sequences
When a valid instruction is received, the communicator performs the sequence
by simulating entering the keys on the keypad. A comma in the SMS is taken
as a pause in the sequence entering.
If you want to remotely reprogram the system it must first be unset and then
switched to programming mode
The number of sequences in one SMS is limited by the maximum size of the
SMS in the GSM network.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-82Y GSM communicator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y GSM communicator in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y GSM communicator

Jablotron JA-82Y GSM communicator User Manual - English - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info