Manual Jablotron JA-80Y - GSM communicator (page 11 of 12) (English)

631261

Zoom out

Zoom in

1/12

The JA-80Y GSM communicator - 11 - MFJ55304

5.33. IP address for data transmission

The communicator supports transmission of special data (e.g. visual

information) from the system to the set IP address, which can be set

by the following sequence:

013 *8 xxx xxx xxx xxx yyyyy *0

where: concerning ∗8, insert these characters, to identify the

following IP address which must consist of 12 digits followed

by 5 digits for the port (see below)

xx..x is the12 digit IP address

y..y is 5 digits for the port (see manual of the communicator).

Example: 013

∗

8 195 039 077 154 07070

∗

To erase the IP set 013∗0.

Note: if no devices supporting this feature are in the system, do not set

the IP address.

Factory default : 77.104.220.129 7070 (img.jablotron.com)

5.34. Locking the ARC settings

All settings which effect reporting to ARCs can be locked by a digital

code:

901 xx..x ∗0 where xx..x is an installer-defined locking code (4 to

8 digits)

Notes:

• Exiting service mode after the locking code has been entered will

lock all the settings effecting ARC communication (see the

sequence list in section 5).

• If ARC programming is locked, then it can be temporally enabled in

service mode by entering 901 xx..x ∗0 where xx..x is the locking

code. It will then relock on exiting service mode.

• The ARC settings can be permanently unlocked by entering 901∗0

while ARC programming is temporally enabled – see above. This

will erase the locking code.

Factory default setting: ARC settings unlocked

5.35. Engineer reset supported

Starting from this version the communicator firmware supports the

Engineer reset feature (also requires the control panel firmware to be

of version KE60108 or higher). This feature is designed for ARC

(Alarm Receiving Centre) connection to satisfy the following

requirements of the DD243 standard: After a confirmed alarm has

been triggered, the control panel must switch to a disabled state.

Switching to normal operation is then only possible using a valid ARC

access code. Until then, the system remains completely disabled –

no operation or programming is possible even when in

Maintenance or Service mode.

An ARC access code can be entered in the following ways:

GSMlink in the field used for remote code entry

SMS instruction

ARC-code_instruction

(e.g. *12345678 STATUS)

6. GPRS modem feature

The communicator can be used as a GPRS modem to connect a PC to

the Internet. A suitable cable is provided with the communicator. The

cable should connect a PC’s serial COM port to thae data connector

on the communicator board (the cable length must not be extended).

It is also necessary to install the driver in the PC, which is found on

the CD ROM provided with the communicator. The SIM card used in

the communicator must be GPRS-enabled and the GPRS parameters

must be programmed in the communicator too (see 5.23). When the

communicator’s GPRS modem function is used:

• It is possible to make phone calls, but the internet data transfer rate

will drop to zero during phone calls

• Incoming SMS messages are stored and are processed after GPRS

data transfer has been terminated.

• GPRS data transfer is terminated if the communicator is due to report

alarms or setting/unsetting (by SMS or by phone call).

7. Further guidance on the communicator

7.1. How the communicator sends reports

If there is a need to report an event (e.g. an alarm) then the

communicator:

• sends data to ARC1, if used (the communicator tries the main phone

number / IP address, if unsuccessful then it tries the backup number /

IP address).

• Then it sends data to ARC2 in the same way if programmed as an

independent ARC. If ARC2 is programmed as the backup to ARC1

then the data will only be sent to it if transfer to ARC1 has been

unsuccessful.

• Then the unit sends SMS reports (1

tel. number, 2

tel. number ….8

tel. number)

• Then the unit performs reporting by phone call (1

tel. number, 2

tel.

number ….8

tel. number) – each programmed number is called once

whether the call has been answered or not

• If all previous attempts to send data to ARCs have been unsuccessful,

the next attempts occur after the programmed repeat period (see

5.28).

If an alarm is cancelled by a user while it is being reported, any unsent

SMSes and unperformed call reports are cancelled, but the ARC still

gets a complete set of reports about events in the system.

7.2. The communicator’s LED

The red LED on the communicator board indicates as follows:

• regular flashing – not registered to a GSM network

• lit permanently – communication in progress (registration to a GSM

network, an SMS transfer or a phone call)

• 3 flashes – pause – 3 flashes… - GPRS modem mode

7.3. After entering service mode the communicator:

• finishes reporting to ARCs (if any is needed) and confirms successful

data transmission by a short ring from the phone connected to the

simulated tel. line

• unfinished SMS and call reports are cancelled

• unsent ARC reports are only erased if ARC tel. numbers / IP

addresses or the ARC communication format or the installation ID are

changed

• alarm restoration reports or fault restoration reports are sent to the

ARC even in service mode

• changes to communicator settings do not take effect until service

mode has been exited

7.4. Configuring the communicator in maintenance mode

If configuring the communicator in maintenance mode is enabled (via

control panel programming), then the above described programming

sequences can be used to set:

• tel. numbers M1 to M7

• the events reported by SMS and phone calls

• GSM signal strength measurement

• simulated phone line functionality

• the digits of the emergency tel. number

7.5. Remote access by Internet

The system can be accessed remotely via www.GSMLink.cz

which

allows complete programming by installers and also operating the

system by end users. To access the system remotely it is necessary

to:

• Use a SIM card enabled for GPRS data transfer

• Program the communicator GPRS parameters (APN) – also

possible via www.GSMLink.cz

• Register the communicator via the GSMLink web page by:

o displaying www.GSMLink.cz

and selecting New registration

o setting your login details (name and password)

o entering the communicator registration code (see 5.19)

o entering the communicator SIM card tel. number

o entering your system access code (user or service – this gives

you access to the user menu or the installer menu accordingly)

o after entering the above parameters it should be possible to

establish a connection with the system (connecting takes time

depending on network traffic, typically within 2 minutes).

• for further access sessions you only need to enter your login details

(these can be memorized by your web browser)

• several people can register for internet access to the system (both

installers and users)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y - GSM communicator in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y - GSM communicator

Jablotron JA-80Y - GSM communicator User Manual - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80Y - GSM communicator Manual

Product: