631259

Jablotron JA-80V - LAN Communicator Manual

4
Zoom out
Zoom in
Previous page
1/10
Next page
The JA-80V LAN / PSTN line communicator - 4 - MKA51202
Function Sequence Options Factory default
ARC communication checking
period
07 a hhmm
a=1 ARC1, a=2 ARC2
hhmm = hours and minutes after last report
(The time to wait after the last report before
performing an ARC communication check)
2400 (24 hours after last report)
Enable ARC reporting (ARC2
backs up ARC1)
00 a x
a=1 ARC1, a=2 ARC2
x=0 reports disabled, x=1 reports enabled, x=2
(only for ARC2) = ARC2 backs up ARC1
ARC reporting disabled
Recording reports sent to ARCs in
the control panel memory
08 x
x=0 no (only records ARC communication
faults, if communication checks are enabled)
x=1 yes (all reports except communication
checks)
yes
Indicate an ARC communication
fault if a report is not successfully
received by an ARC within 110
sec of transmission.
09 x
x=0 no
x=1 yes
no
IP address for data transmission
013 xx..x ∗0
IP address and port in format – e.g..: 013
∗8 077 104 220 129 07070 ∗0
∗8 mark IP address which must contain 12 digits
followed by 5 digits for the port.
Entering 013∗0 IP erase the setting
77.104.220.129 7070
(img.jablotron.com)
Locking the ARC settings
901 xx..x ∗0
xx..x = an installer-defined locking code (4 to 8
digits). Entering this code and then exiting
service mode will lock the ARC settings
901∗0 will erase the code (= permanently
unlocked)
unlocked
Unlocking the ARC settings
900 xx..x ∗0
xx..x = a locking code used by sequence 901
ARC programming can be temporarily
enabled in service mode by entering this
sequence. It will then relock on exiting service
mode
These parameters effect reporting to the ARC and it is impossible to change them if the ARC settings are locked.
* These parameters cannot be programmed from the system keypad, but they can be programmed by sending SMS instructions or by Comlink software.
5.1. Language setting
Language of the text used by the communicator can be set by
instruction:
981 xx
Where:
xx is number of the language – see the following list:
01 EN English 10 FI Finnish
02 CZ Czech 11 NO Norwegian
03 SK Slovak 12 SV Swedish
04 NL Dutch 13 FR French
05 DE German 14 HU Hungarian
06 PL Polish 15 RU Russian
07 DA Danish 16 TR Turkish
08 IT Italian 17 SP Spanish
09 PT Portuguese
Note:
Set the language before editing the text in the system (change of
the language will change the text to the factory default)
Change of the language in the communicator will automatically
result in changing the language in the connected keypad (also the
wireless keypad if connected)
Set language will not be change when reset is performed
Example: by setting 98102 the Czech language will be set.
Factory default : 98101 = English
5.2. Programming tel. numbers for reporting to phones
See part 4.
5.3. Selection of the events reported to phones
The factory-default list of reported events and their assignment to
telephone numbers M1 to M8 can be altered by this sequence.
The complete list of reportable events is shown in the following
table.
It is possible to select whether the event should be reported by an
SMS or by a phone call, or by both an SMS followed by a phone call
Each event has pre-programmed factory-default SMS text. These
texts can be edited (see 5.4). The acoustic signals for phone call
reporting are fixed and cannot be changed (e.g. an alarm is
indicated by a siren sound if a reporting call is answered)
List of events which can be reported to phones and their factory-default assignment to particular phone numbers
Phone number memory M
ec Event
1 2 3 4 5 6 7 8
01 Intruder alarm - instant S S SC SC SC SC C
02 Intruder alarm - delayed S S SC SC SC SC C
03 Fire alarm S S SC SC SC SC C
04 Panic alarm S S SC SC SC SC C
05 Number of permitted incorrect code-entries
exceeded
S S SC SC SC SC C
06 Alarm triggered during control panel
power-up
S S SC SC SC SC C
07 Tamper alarm S S S S S S
08 End of tamper alarm
09 End of alarm indication
10 Alarm cancelled by user S S S S S S
11 Setting S S
12 Unsetting S S
13 Partial setting S S
14 Codeless setting S S
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80V - LAN Communicator at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80V - LAN Communicator in the language / languages: English as an attachment in your email.

The manual is 0,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info