554884

Jablotron JA-60GSM Manual

5
Zoom out
Zoom in
Previous page
1/6
Next page
User manual JA-60GSM - 8 - MFJ51808
3.3. SMS texts editing
The list of SMS texts stored in the dialer consists of texts reported as event reports (installation
name, event name and source name) and texts for remote control instructions. All these texts can be
edited by the following SMS sent from a mobile phone.
yyyyy∗TXT∗z,text, z,text
where:
yyyyy is the remote access code; default setting is 1111; this code can be changed,
see section 4.1
TXT is the text programming command
z is the text index (110 - 711 see table 3.3.1).
, comma (separator)
text is the new text string. Neither a comma nor a dot can be used inside the text. Space
inside the text is a valid character (dialer ignores spaces out of the “text” string)
∗ separator (asterisk or space)
Note: If you change texts of command SMS this way (texts no. 703 to 711), then you will actually
change the commands which the system reacts to. E.g.: if you change text „MO“ (text no. 705) to
„STATE OF THE ALARM SYSTEM?“ then this command can only be used to learn the status of the
system. You can change texts for your needs and also insert a password to protect against
unauthorized use of SMS commands.
Example: If the factory default code for the dialer is 1111, then the sending of SMS:
1111*TXT*201, uncle Sam’s controller, 202, aunt Mary’s controller to the dialer will change names of remote
controllers No. 1 and 2.
3.3.1. Table of SMS texts
Text index z Factory default text Text index z Factory default text
110 Master code 301 Wired detector #1
201 Controller #1 302 Wired detector #2
202 Controller #2 303 Wired detector #3
203 Controller #3 304 Wired detector #4
204 Controller #4 305 Wired detector #5
205 Controller #5 306 Wired detector #6
206 Controller #6 307 Wired detector #7
207 Controller #7 308 Wired detector #8
208 Controller #8 309 Wired detector #9
501 User code #1 310 Wired detector #10
502 User code #2 311 Wired detector #11
503 User code #3 312 Wired detector #12
504 User code #4 313 Wired detector #13
505 User code #5 314 Wired detector #14
506 User code #6 315 Wired detector #15
507 User code #7 316 Wired detector #16
508 User code #8 401 Wireless detector #1
509 User code #9 402 Wireless detector #2
510 User code #10 403 Wireless detector #3
511 User code #11 404 Wireless detector #4
512 User code #12 405 Wireless detector #5
513 User code #13 406 Wireless detector #6
514 User code #14 407 Wireless detector #7
700 Alarm system reports: 408 Wireless detector #8
703 AM 409 Wireless detector #9
704 DM 410 Wireless detector #10
705 MO 411 Wireless detector #11
706 ME 412 Wireless detector #12
707 AUXON 413 Wireless detector #13
708 AUXOFF 414 Wireless detector #14
710 PGON 415 Wireless detector #15
711 PGOFF 416 Wireless detector #16
User manual JA-60GSM - 5 - MFJ51808
2. SMS and audible alarm reports setting
The factory default settings allow the GSM dialer to send SMS reports and audible warnings when the
control panel generates important pertinent information (alarms, arming, etc.). It is only necessary to set the
telephone numbers to where the information should be reported. If you want to report additional or different
events than the factory default provides, see section 3.
The following information is for use by an alarm system administrator who knows the master code.
All settings can be programmed via a keypad. A sequence can be canceled anytime by pressing the
“N” key (e.g. entry error). When a sequence is complete, the system will store it into the memory. The
following settings are made in the user mode, which can be entered by:
F 0 master code. (this mode is indicated by the “U” character on the keypad’s LED display).
Example:
If the master code is 1234 then enter: F0 1234
Press “N” to exit the user mode.
2.1. Telephone numbers setting
The dialer has 8 telephone number memories. Each memory has particular SMS reports assigned to
it and/or audible warnings according to the default setting – see table 2.2. By entering a telephone
number to a particular memory selects what will be reported to this number:
7t xxx...x F0
where:
t is a memory from 1 to 7
xxx...x is a telephone number (max. 20 digits), enter F9 before the number, if you need
+ prefix for international calls. To use an attached SMS phone set enter code
001 instead of the telephone number
To disable reporting to a particular number, delete this number from the memory by entering:
7tF0
where:
t is a memory from 1 to 7
Report testing:
If you wish to report any alarm, arming and disarming via an SMS followed by a notifying call and your
mobile phone number is 123456789, then enter 75123456789F0 (while the control panel is in the
programming mode).
Then exit the programming mode by pressing the N key. Now when you arm the system your mobile
phone will receive a reporting SMS.
Notes:
For SMS transfers use only numbers of mobile phones or call centers that can transfer SMS
messages.
Audible warnings can be used on both GSM and landline networks.
The GSM dialer can report all event information from the alarm system via SMS and audible
warnings. The setting of reported events for all numbers can be changed – see chapter 3.
2.2. Telephone numbers table
Memory
Entering
sequence
To this pair of numbers will be sent (factory default): Telephone numbers
1. 71 ____ F0
2. 72 ____ F0
- ALARM SMS
- Technical SMS
5


Need help? Post your question in this forum.

Forumrules
1

Forum

jablotron-ja-60gsm

Reset search

  • Suddenly the system stopped and no communication with the main door panel Submitted on 24-9-2021 at 12:18

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60GSM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60GSM in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-60GSM

Jablotron JA-60GSM Installation Guide - English - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info