554883

Jablotron GD-06 Manual

2
Zoom out
Zoom in
Previous page
1/5
Next page
GSM communicator GD-06 Allegro – complete manual 2/5 MHG 51203
• From a GSM phone, you can send an SMS instruction to switch on
or off the P5 and P6 outputs (example: “ON P5”, “OFF P6”).
• You can also switch the relay on or off by making a phone call to
the GD-06 from a phone registered to TEL1 or TEL2 memory
positions. The GD-06 ALLEGRO doesn’t answer this call, so you
are not charged any telecommunication fee for this remote control.
Notes:
1. You can remotely control the GD-06 from any phone: not only from
the ones stored in the memory TEL1-TEL8. You must just add the
master (default MASTER) or a user (default USER) access code in
front of the instruction.
Example: “MASTER ON P5”
2. The SMS instruction texts are case insensitive. This means that
the instruction “ON P5” is equal to “on p5”.
2.4. Access codes MASTER - USER
Parameter settings:
You can set the communicator without using the MASTER access code
if the jumper MASTER is in the NO MASTER position. If it is in the
MASTER position, then a valid MASTER code must be used. (see
figure 1)
For quick installation it is recommended to set the jumper to the NO
MASTER position. However, for security reasons, during normal
operation the jumper should stay in the MASTER position
3. Advanced setting
General rules for following SMS setting sequences:
1. Jumper is in the MASTER position (it means that the MASTER
code is required)
2. Setting sequences are not case sensitive.
3. Key words must be separated with a space
4. In the examples are used the SMS text, which will be set after the
RESET EN (factory default setting).
5. There can be multiple commands in one SMS, which must be
separated with comma and a blank space.
3.1. Setting of inputs INP
Terminals P1 to P6 can be programmed as inputs. A single SMS
must be always used to program the input, desired parameters as
well as the corresponding phone numbers. If it is necessary to
reprogram the input (for example to add another phone number), all
previously set parameters must be in a new programming SMS sent
again.
MASTER PX INP TYz TYz
Where:
X is the number of terminal P1 – P6
Y is the position of the phone number to which the SMS will be
sent
Z + , – or nothing, depending on the required function
Setting of inputs
Parameter Description
P1, P2, … P6
The name of the terminal which will be programmed as
input via SMS*
INP Parameter for programming a terminal as an input
T1, T2, ….T8 Phone numbers (TEL1 to TEL8)
+ Activation (connecting to GND) will cause sending SMS
-
Deactivation (disconnecting from GND) will cause
sending SMS
Without + or – parameters the SMS will be sent in case
of any change of input (connecting/disconnecting
to/from GND)
DEL
All previous settings will be erased. No confirmation
SMS will be sent.
* Description of terminal can be changed, but P1, P2 etc, must be
always used in the setting sequences.
tab. 2
Examples of setting SMS:
MASTER P1 INP T2 T3
- Terminal P1 will be set as an input, message about any change of
the input will be sent to TEL2 and TEL3
MASTER P3 INP T4+ T7 T8-
- Terminal P3 will be set as an input, TEL4 will be notified on
activation, TEL8 on deactivation and TEL7 will be notified on all
changes of the input.
MASTER P6 DEL
- All previous settings for terminal P6 will be deleted. The terminal will
be programmed as an input, information about the change will not be
sent to any phone number
Note:
The input signals shorter than 200ms (factory default) will be ignored.
The input filter can be adjusted from 50ms up to 20 seconds.
There are analog inputs, which have adjustable level of their activation
and deactivation (hysteresis). They can also be used for measuring of
analog values (voltage).
Both settings can only be changed via GSMLINK web page. Factory
default setting will be automatically restored after reset.
3.2. Setting of outputs OUT
Relay (NO,C,NC) is always output, terminals P1 to P6 can be
programmed as outputs. A single SMS must be always used to
program the output, desired parameters as well as the
corresponding phone numbers. If it is necessary to reprogram the
output (for example to add another phone number), all previously set
parameters must be in the programming SMS sent again.
MASTER PX OUT parameters or for output relay:
MASTER RELAY parameters
Where:
X is number of terminal P1 – P6
RELAY is the relay output
Parameters parameters according to table 3
Setting of outputs
Parameter Description
P1, P2, … P6
RELAY
The name of the terminal, which will be programmed
as output via SMS*
OUT Parameter for programming a terminal as an output
T1, T2, ….T8
ALL
Phone numbers TEL1 to TEL8, from which will be an
output terminal switched on or off when dialling in
- the output will be controlled by a phone call from all
saved phone numbers
INT
s,m,h
Activation of the output for the preset period of time –
after dialling-in or DTMF code
- duration is programmed by number (selectable from
1 to 99) and unit s-second, m-minutes, h-hours
NEG
Negation of the output status – after dialling-in or
DTMF code
DTMF
To set the controlling DTMF code. The output will be
controlled when the correct DTMF code from the
telephone keyboard of the phone, which is calling to
the Allegro, is received. It is important to enter DTMF
codes without any repetition in their sequencing. For
example If there is code 123, it is not possible to use
another code 12345 - after receiving the initial 123 it
is recognized as the correct code, the command will
be performed and 4 will be considered as the
beginning of a new code.
Figures 0, 1, … 9,*,# can be used; (up to 10 digits)
TEMP
To set a temperature switch – if the temperature drops
below the preset level (set in °C) the output will be
switched on. Hysteresis is 0,5 °C
(hysteresis is adjustable only via www.gsmlink.cz
)
DEL
All previous settings will be erased. No confirmation
SMS will be sent.
* Description of position can be changed, but P1, P2 etc, must always
be used when programming setting sequences.
tab. 3
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron GD-06 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron GD-06 in the language / languages: English as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron GD-06

Jablotron GD-06 User Manual - English - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info