555040
4
Zoom out
Zoom in
Previous page
1/6
Next page
GSM car alarm CA-1802 „Athos“ 4/6 MHF57202
Factory default setting is SET 1001111101 (bold letters in the text).
If you want to change only particular DIP or SET parameters, enter x for the
others (i.e.
MASTER SET xx2xxxxxxx will set an extended locking signal for
closing the windows).
8. User instructions
8.1. Remote control arming and disarming
Button
is used to arm and lock the vehicle completely. Using the
button the car can be disarmed and unlocked. If you re-press the
button within 15 seconds after arming, partial arming occurs (confirmed
acoustically). In this mode, the internal wireless detectors are not active,
nor is the low voltage sensor. Also no voltage is supplied for external
sensors. Using the CR-11A module, pressing the buttons
and
together allows you to use additional functionality (e.g. switching
independent heating).
8.2. SMS control from an authorized phone
Text SMS Description
AM
ARM and lock the car
AM EXT
Partially ARM and lock the car
DM
DISARM and unlock the car
IMO
STOP (immobilize) the car (after turning ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
Car alarm will reply with status information, e.g. „car
reports: Time: 27.01.04 13:04, Status: Armed, Unblocked,
Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC xxxx
To change the user code. xxxx is the new user code, 4 to 8
characters (A –Z & 0 – 9). Factory default user code is
USER
CREDIT
parameter
To obtain the balance of a prepaid SIM card if used. See
12.6-8 for details
AUX
parameter
To operate CR-11A output relays as well as the appliances
or circuits that are connected to these relays (see par. 13)
HF abcdef
Hands-free set adjustment:
a – enable calls (0= disabled, 1=enabled)
b – auto answer incoming calls (0= disabled, 1=enabled)
c – microphone sensitivity 0 to 9, (5)
d – speaker volume 0 to 9, (5)
e - ringing tone volume 0=mute to 9= max., (5)
f – ringing sound 0 to 9, (1)
SIREN
To activate the siren for 30 seconds
The instruction must contain spaces (e.g. HF 105551).
If an SMS instruction is sent from an unauthorized phone, it is
necessary to put a user code before the instruction (default is USER).
Again, a space is necessary. An example of arming from an
unauthorized phone: USER AM
SMS instructions are not case-sensitive. Only basic ASCII can be
used in the SMS instruction texts.
If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway which adds more text –
advertisements etc. When using the % character it is always
necessary to insert the Master or User code followed by a space
before the command itself.
SMS instructions can be renamed. Example: It is possible to replace
“AM“ by “LOCK“.
The parameters in bold are factory defaults.
8.3. Dialling-in remote control
Complete remote control by dialling-in from an authorized phone is
possible (see table DIP – parameter E). If you dial the car alarm number
from an authorized phone, it will cause a change of state (arming,
disarming, etc.). A call to the alarm is free of charge (the car alarm will not
answer the incoming call). If operated by dialling-in after an alarm has
been triggered, a slight delay can occur. If disarmed by dialling-in after
partial arming, then a subsequent dialling-in will cause complete arming.
Change of state after dialling-in can be confirmed via SMS (optional).
8.4. Phone calls by handsfree set (HF-03)
If the HF-03 hands free set is installed, it is possible to receive calls
and to dial pre-programmed phone numbers DIAL x. When the
ignition key is on, the remote control (RC-8x) allows you to operate
the hands free set. The call is done via the car alarm’s SIM, the
handsfree set is not usable for other phones.
Incoming calls – to answer them, press any button on the RC-8x
remote control. By pressing any button again, the call will be
terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on, the RC-8x allows you
to call up to 4 pre-programmed numbers (see chapter 5.1).
When armed, all incoming calls are automatically rejected. If the car
is immobilized or after an alarm has been triggered all calls are
automatically answered (it is possible to listen in).
8.5. Alarm
When an alarm is triggered, the siren will sound for 30 sec., warning
SMS messages will be sent to all phones (TEL1 to TEL4) and these
phones will also be called with the siren sound. If automatic location is
turned on, a request for location detection is sent. After the user stops the
alarm, all transmissions are terminated.
To stop the alarm, disarm the alarm by pressing the
button on
the remote control or by a disarm SMS instruction (DM). The DM
instruction unlocks the car at the same time. After the alarm has been
stopped by a user in a regular way, an SMS will be sent informing
about alarm termination.
Example of an alarm SMS:
Your car reports: Alarm, INP activation, Time 10.12.04 01:45
Mercedes reports: Alarm, FIRE, garage sensor activation, Time 11.02.04
01:12
8.6. Acoustic signalling of arming/disarming
If acoustic signalling is ON (see table 6), the arming is confirmed by
1 beep and disarming by 2 beeps. Partial arming is indicated by two
short beeps. Three beeps while disarming the car indicate that an
alarm was triggered during the armed state. If arming a car with an
active alarm input (e.g. open car boot) arming is supplemented by four
short beeps. The siren will also indicate triggering of a wireless
detector which provides an entrance delay (by a single beep).
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot)
or comma cannot be used in the text, spaces are
allowed
Example: MASTER TXT 01,LOCK PLEASE
Text numbers 01 to 26 are instructions requiring a MASTER code for
their modification. If you modify these texts, you change the
instructions which the car alarm will respond to. For example, replacing
“STATUS” with “STATE PASSWORD” will cause that state detection
will be obtainable by “STATE PASSWORD” only. This way you can
insert a “password” into the texts which prevents misuse. All other
texts are of informational character and correspond to particular
events, states and input names. This allows you to adjust the names to
a form which suits you well. For example, “INP 1” can be replaced with
“bonnet” etc. Texts can be replaced using the MASTER code as well
as the USER code (optional).
A convenient way for text modification is to use the GSMLink web
page, see paragraph 11.
SMS text table
zz Factory default text zz Factory default text
SMS commands: 48 Telephone 4
01 AM 49 Telephone UC
02 DM 50 Telephone – MC
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCATOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN Status information:
16 SIREN 64 Car alarm reports
17 SET 65 Status:
18 AUXA 66 Armed
19 AUXB 67 Disarmed
25 ON 68 Ignition key ON
26 OFF 69 Ignition key OFF
Events: 70 Engine is blocked
30 Alarm 71 Engine is unblocked
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-1802 - Athos GSM RESET 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-1802 - Athos GSM RESET 1 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron CA-1802 - Athos GSM RESET 1

Jablotron CA-1802 - Athos GSM RESET 1 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info