707696

Italiana Camini Point Plus Manual

28
Zoom out
Zoom in
Previous page
1/202
Next page
- 28 -
ENGLISH
SMOKE OUTPUT
POINT PLUS is designed for the connection of the • ue at the
top, back or side left of the stove.
FOR THE CONNECTION OF THE SMOKE OUTPUT
TO THE CHIMNEY, WHETHER FROM THE BACK,
SIDE OR TOP, IT IS NECESSARY TO REMOVE THE
CORRESPONDING METAL SIDE LEFT.
To connect:
- Loosen (by about 15 mm) the two screws on the cast iron top
under the steel cover (A - ! g. 1).
- Open the door and remove the galvanised panel (B1 - ! g. 2)
- Loosen the screw on the lower/front part of the left side (B -
! g. 2).
- Remove the screw above the top (see ! g. 5 on page 29)
- Remove the metallic left side, moving it about 2 cm towards
the front of the stove, extracting it ! rst from below and then
pulling it out from under the top (! g. 3).
At this point, choose the necessary • ue connection.
REAR SMOKE OUTPUT CONNECTION
Fit the elbow joint to the smoke extractor unit vent (C- ! g. 4)
with the band provided.
Connect the side smoke output pipe (not provided) to the afore-
mentioned elbow joint.
In this case it is suf! cient to make the smoke output pipe (not
provided) pass through the hole in the lower part of the sheet
metal back (! g. 4).
SIDE SMOKE OUTPUT CONNECTION
Fit the elbow joint to the smoke extractor unit vent (D- ! g. 5)
with the band provided.
Connect the side smoke output pipe (not provided) to the afore-
mentioned elbow joint.
Remove the pre-cut diaphragm from the sheet metal side to al-
low the smoke output pipe (not provided) to pass through (! g.
5).
Complete the operation by applying the closure rosette pro-
vided (E - ! g. 6) using the screws provided, after replacing the
metal side.
N.B. The rosette and the metal side must be ! tted after the • ue
has been de! nitively ! xed.
TOP SMOKE OUTPUT CONNECTION
Connect the rear smoke output pipe (not provided) to the
smoke extractor unit vent (D - ! g. 7) with the band provided.
In this case, it is necessary to use the two sheet metal half-cov-
ers provided (G - H - ! g. 7), instead of the whole sheet metal
cover, and to eliminate the galvanised cap (I - ! g. 8).
Remove the diaphragm from the small metal half-cover (G -
! g. 7) to allow passage of the pipe.
AFTER COMPLETING THE CONNECTION OF THE
SMOKE OUTPUT PIPE TO THE FLUE, REPLACE THE
METAL SIDE AND THEN CONTINUE WITH THE AP-
PLICATION OF THE CASING.
INSTALLATION
A
! g. 1
! g. 3 ! g. 4
! g. 5 ! g. 6
! g. 8
! g. 7
! g. 9
C
D
E
G
H
I
B
B1
! g. 2
D
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Italiana Camini Point Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Italiana Camini Point Plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 10,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info