462566
11
Zoom out
Zoom in
Previous page
1/22
Next page
11
4
Start the wash-cycle by pressing the Start button (S) and releasing it immediately.
The door is sealed and the cycle-LED lights up.
During the first 2 minutes after starting, the program number is blinking and you
can change the program in case of a possibly wrong selection.
To do so, select another program with the SELECT button (P). This new program
will start immediately.
Start the machine
Display information
The left display will indicate the temperature of the wash bath - in °C or °F (on
machines where this function has been selected).
The central display shows the remaining time to the end of the wash cycle.
Indications of program
sequence
For programs which are being run for the first time, the machine will take a
theoretical time estimate. If this time indication does not correspond to the real
cycle time, the cycle time will be corrected from the second cycle onwards
(Self-Teaching function of the machine).
This correction will have to be preprogrammed and is not activated on
program numbers higher than 20. The corrected time will also be lost when
the power has been cut from the machine for more than 24 hours.
The right display will continue to show the selected program number.
If a Level-stop was programmed (which halts the programmer during the filling
of the cylinder) and/or a Heat-stop (which stops the programmer during the
heating up of the wash bath, then the respective LED’s light up in the display.
Once the required water level and/or temperature have been reached, the LED
is turned off and the internal programmer advances again.
Wash cycle-LED’s
Each program segment has a corresponding LED. Each of these 6 LED’s light up
when the appropriate segment is executed. This way, the program sequence can
be accurately followed.
When a LED blinks, the machine is taking up water.
When a LED blinks slowly, the machine is heating up the water.
Spin-LED’s
When the water is drained at the at the end of a program segment and the machine
spins if so desired, the left spin-LED (intermediate spin) will light up together with
the cycle-LED.
- Functioning of the spin-LED’s during intermediate spin:
- Functioning of the spin-LED’s during gentle-intermediate spin:
LED drain/distribution low spin coast
Interm. spin blinking rapidly blinking slowly blinking slowly
LED drain/distribution low spin coast
Interm. spin blinking rapidly continuously continuously
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for IPSO HF 176 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of IPSO HF 176 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info