459176

Inverto IDL5550S Manual

20
Zoom out
Zoom in
Previous page
1/124
Next page
En
17
There are three ways to update the software of the digital receiver:
Over The Antenna (OTA), Over The Cable (OTC), and through the USB port. In the next chapters you can nd
more detailed information about OTA and OTC. From the Settings Menu, select System Information and then
Software Update.
SOFTWARE UPDATE VIA ANTENNA (OTA)
If “Auto Upgrades” in the User Preferences is set to “Auto”, the receiver will do this all in the background during
stand by. At the rst start after such an update, the receiver will show you a popup message with the information,
that your receiver got a successful update.
During the OTA software update, the unit will rst search for the update signal.
During the search, a message box “Software update” will be displayed on the TV screen – this process may take
several minutes. To stop this process, press the “Red” function key or “Exit” key. If new software is available,
the user will be informed and asked to conrm the download.
The user will be asked to conrm the download two times, to help prevent accidental changes.
During the download, the “OTA” message will be displayed on the TV screen, showing the progress bar. After all
data has been received, the receiver will update the current software and automatically restart.
All user preferences and channel lists will remain unchanged.
Note: OTA Updates are broadcasted over ASTRA 19.2E satellite and therefore are not available in all the
countries.
SOFTWARE UPDATE VIA SERIAL CABLE (OTC)
In order to update the software using the service port on the rear panel, the user will require a RS232 cable, PC
with RS232 connection, and terminal software for the PC, such as HyperTerminal in Windows.
The user must also have the software le, which can be downloaded from the internet at www.ftacom.com.
To update the software using the cable, use the following steps:
1 – Switch the digital receiver off using the main power switch on the rear panel.
2 – Connect the digital receiver to the PC using a RS232 cable.
3 – In the terminal software of the PC, open a communication port with following parameters: 115200bps, 8bit,
1stop bit, no parity and no ow control.
4 – Select the new software le to send to the unit and set the protocol to 1k X modem.
5 – Start sending the le.
6 – Switch on the digital receiver to start the loading procedure.
During the transfer, the receiver will display the message “OTC” with a progress bar. After the le has been
received and unpacked, the digital receiver will update the current software and automatic restart. All user
preferences and channel lists will remain unchanged.
SOFTWARE UPDATE VIA USB
The software can be updated using a USB mass storage device.
To update the software using a USB mass storage device, you will require the new software le from our website
and a USB device, such as a USB hard disk or memory stick.
a) Copy the software bin le to the root folder of the USB mass storage device.
b) Make sure the receiver is switched off.
c) Turn the receiver On while the “+” button is pressed until “On The USB” messaged is displayed on
the front panel display
d) Insert the USB mass storage device into the USB slot on the front panel of the receiver.
e) The receiver will automatically copy the new software from the USB device into the receiver.
After the le has been installed and unpacked, the receiver will update the current software and automatically
restart. All user preferences and channel lists will remain unchanged.
Caution: Be careful not to interrupt the software installation by removing the USB stick, turning off the receiver,
or otherwise interrupting the installation process. If the installation is interrupted by accident, such as by a
power failure, the receiver may not boot up afterwards. If so, you can recover normal operation by installing new
software using the RS232 connection, or by returning the receiver for service.
Note: Installation of a complete software bundle, including boot loader, will reset all user settings and erase the
channel list. The library will remain unchanged.
Software update
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDL5550S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDL5550S in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info