459176

Inverto IDL5550S Manual

10
Zoom out
Zoom in
Previous page
1/124
Next page
En
7
NOTES
Spent batteries should not be discarded in your domestic refuse. In most countries, you are legally •
obliged to ensure spent batteries are properly recycled. They can be disposed of either in special bins
provided in your community, or may be returned to any retailer who sells batteries.
Use the batteries correctly to avoid possible leakage and corrosion. Do not touch the liquid with bare •
hands, should leakage occur.
Do not use a new battery with an old battery, or batteries of different manufacturers.•
Do not attempt to recharge the supplied batteries•
If you do not intend to use the remote for an extended period of time, remove the batteries.•
If battery leakage occurs, wipe out any liquid inside the battery compartment and insert new batteries.•
USING THE REMOTE CONTROL
For best results, point the remote control directly at the receiver while pressing keys•
Do not place the receiver in a location exposed to direct sunlight or bright uorescent lighting, as this •
may interfere with the receiver and cause it not to respond to the remote.
Setup
This short instruction explains the most important functions to ensure that you can directly watch television with
your new digital receiver. Please note, additional adjustments may be required.
CONNECTING TO THE ANTENNA
Note: Do not connect the digital receiver to the main power yet.
CONNECT THE LNB (LOW NOISE BLOCK) TO THE DIGITAL SATELLITE
RECEIVER INPUT
Connect the LNB on the satellite dish antenna directly to the digital receiver using the “LNB in” connector of the
Tuner, by means of a coaxial cable. You may use the loop-through connector to connect to a second receiver.
CONNECTION TO THE TV SET
The digital receiver and TV set can be connected by means of a SCART cable (supplied), HDMI cable
(supplied), Component Video cables (not supplied) or Composite Video (Yellow) and Stereo Left/Right Audio
cable (Red+White).
Simply connect the two ends of the cable you select to use in connecting the receiver to the TV set. The SCART
connection ensures that audio and video signals are transmitted to the TV set in optimum quality.
In case your TV set is equipped only with a CVBS input socket, you can use the CVBS output on the digital
receiver and connect your TV set via cable to provide optimum quality of the video signal. To provide audio
signal to the TV set it is necessary to connect the Audio L/R output on the digital receiver to the audio input on
your TV set.
The HDMI connection is recommended for Digital TV. In case the TV has a HDMI input connector, a special all-
digital interface that provides the highest picture quality, connect the product to the TV with the HDMI cable.
The Component Video connection is also recommended for Digital TV. Connect the receiver to the TV with the
Component cable as shown in the diagram.
CONNECTION TO A DVD OR VIDEO RECORDER
Just as the TV set, the DVD or video recorder is connected to the receiver via a SCART connection. Use the
VCR SCART socket for this purpose.
CONNECTION TO A HI-FI SYSTEM
The audio quality of digital TV and radio programmes can be enjoyed even more when reproduced through a hi-
audio system. To do this, use a RCA cinch stereo cable to connect the sockets marked Audio L/R on the receiver
to one of the inputs of your hi- system marked either Line, Aux or Extra.
If your hi- system is equipped with a digital audio input, you may use a digital RCA cinch cable to connect the
electrical (Coax) digital audio output of your receiver (socket DIGITAL AUDIO COAX) to your hi- or Dolby Digital
system. The receiver is also equipped with an optical digital output. If your hi- system is equipped with an
optical audio input, you may use an optical cable to connect your hi- system to your digital receiver.
CONNECTION TO MAIN POWER SUPPLY
After all the connections are done you can connect your digital receiver to power. Just before plugging a power
cable into the wall connector put the power switch, on the rear panel, in position 0 (off).
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDL5550S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDL5550S in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info