694976

Inventum VKI 3010 ZWA Manual

18
Zoom out
Zoom in
Previous page
1/40
Next page
installation instructions
7
problems & solutions
8
• Safety during use is only guaranteed if the assembly has taken place in a technically correct way and in accordance with this
installation instruction. The installer is liable for damage caused by an incorrect assembly.
• The cooker falls under protective class I and may only be used in combination with an earthed connection. The manufacturer
is not liable for unsuitable operation and possible damage caused by unsuitable electric installations.
• The cooker must be connected to a permanent installation in which provisions for switching off are integrated, in accordance
with the installation instructions.
• Make sure that the power supply cable does not get jammed during installation or is running along sharp edges. If an oven is
installed below it, make sure the cable runs via the rear corners of the oven to the connection box. It must be placed in such a
way that no contact is made with hot parts of the cooker or oven.
• The connection point, socket and/or plug must always be accessible.
• The worktop on which the cooker is placed must be flat, horizontal and stable. Observe the instructions from the manufacturer
of the worktop.
• In case of incorrect installation or connection, the warranty becomes invalid.
• Attention: any change within the appliance, including replacement of the power supply cable, must be performed by an
authorised installer.
• Sufficient space around the cooker is required for safe use. Check that this space is available.
• The distance from the cooker to an extraction hood should be at least 650 mm.
ELECTRICAL CONNECTION
Caution: this cooker is always supplied with a cord and plug. The connection is a 1 phase connection.
• Check that the voltage corresponds with what is stated on the information plate.
• Connect the cooker to an earthed socket.
• Caution: The connection point should always be within reach.
Problems Checkpoints and solutions
After inserting the plug in the socket and switching
on the induction cooker with the [ ON/STANDBY ]
key, the [ ON/STANDBY ]
indicator on the display does not light up.
• Is the plug properly inserted in the socket?
• Has the socket, fuse or cord been damaged?
The induction cooker makes a lot of noise.
The electronics of the induction cooker require cooling. It is normal for
the fan to make noise.
Error message
E0 No pan or no suitable pan has been placed.
E1 Temperature sensor defective. Contact customer service.
E2 Operating panel defective. Contact customer service.
E3 Voltage too high. Have your connection checked by an electrician.
E4 Voltage too low. Have your connection checked by an electrician.
E5
The operating panel is overheated. Switch off the cooker and wait until
it is cooled down.
E6
The cooker is overheated and switched off automatically. Check the
ventilation openings and allow the cooker to cool down. The induction
cooker will function normally again.
18 • English
VKI3010ZWA-instructions.indd 18 13-9-2018 09:25:05
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum VKI 3010 ZWA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum VKI 3010 ZWA in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info