771741
23
Zoom out
Zoom in
Previous page
1/140
Next page
Page 23
8
Wiring
Safety Precautions
Outdoor Unit Wiring
WARNING
Be sure to disconnect the power supply before
working on the unit.
All electrical wiring must be done according to
local and national regulations.
Electrical wiring must be done by a qualied
technician. Improper connections may cause
electrical malfunction, injury and re.
An independent circuit and single outlet must
be used for this unit. DO NOT plug another
appliance or charger into the same outlet.lf the
electrical circuit capacity is not enough or there
is a defect in the electrical work, it can lead to
shock, re, unit and property damage.
Connect the power cable to the terminals and
fasten it with a clamp. An insecure connection
may cause re.
Make sure that all wiring is done correctly and
the control board cover is properly installed.
Failure to do so can cause overheating at the
connection points, re, and electrical shock.
Ensure that main supply connection is made
through a switch that disconnects all poles, with
contact gap of a least 3mm (0.118”).
DO NOT modify the length of the power cord
or use an extension cord.
WARNING
Before performing any electrical or wiring
work, turn o the main power to the system.
CAUTION
Connect the outdoor wires before connecting
the indoor wires.
Make sure you ground the unit. The ground-
ing wire should be away from gas pipes, wa-
ter pipes, lightning rods, telephone or other
grounding wires. Improper grounding may
cause electrical shock.
DO NOT connect the unit with the power source
until all wiring and piping is completed.
Make sure that you do not cross your electrical
wiring with your signal wiring, as this can cause
distortion and interference.
Follow these instructions to prevent distortion
when the compressor starts:
The unit must be connected to the main
outlet. Normally, the power supply must
have a low output impedance of 32 ohms.
No other equipment should be connected
to the same power circuit.
The unit’s power information can be found
on the rating sticker on the product.
TAKE NOTE OF FUSE SPECIFICATIONS
The air conditioner’s circuit board(PCB) is
designed with a fuse to provide overcurrent
protection. The specications of the fuse are
printed on the circuit board, such as:
Indoor unit: T5A/250VAC,T10A/250VAC. (ap-
plicable for unit adopts R32 refrigerant)
Outdoor unit: T20A/250VAC(for <24000Btu/h
unit),T30A/250VAC(for >24000Btu/h unit)
NOTE: The fuse is made of ceramic.
1. Prepare the cable for connection
a. You must first choose the right cable size
before preparing it for connection. Be sure
to use H07RN-F cables.
Table 8.1: Minimum Cross-Sectional Area of
Power and Signal Cables North America
Rated Current of Appliance (A) AWG
<7 18
7-13 16
13-18 14
18-25 12
25-30 10
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventor V6MKI32-WiFi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventor V6MKI32-WiFi in the language / languages: English, German as an attachment in your email.

The manual is 22.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Inventor V6MKI32-WiFi

Inventor V6MKI32-WiFi User Manual - English, German - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info