686153
16
Zoom out
Zoom in
Previous page
1/23
Next page
(328PO) MODEL ZS6110 OZONE & SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2017
328
PO
SAVE THESE INSTRUCTIONS
English
Page 16
MAINTENANCE
Flow Sensor Cleaning
1.
In a counter-clockwise motion unscrew the collar of the flow sensor
(7)
and remove it from
the electrolytic cell conduit. See “Part Reference”.
2.
If deposits and debris are seen on the surface of the flow sensor, then use a garden hose
to wash it off.
3.
If flushing with water does not remove the deposits, use a plastic brush to clean the surface
and the hinge if necessary. Do not use a metal brush.
4.
After the flow sensor has been inspected and cleaned, align the locator notch on the flow
sensor to the connection ridge in the conduit. Now turn the collar in a clockwise motion,
tightening the sensor back into its position. Do not overtighten.
Electrolytic Cell Cleaning
The electrolytic cell has a self cleaning function incorporated into the electronic control's
programming. In most cases this self cleaning action will keep the cell working at optimum
efficiency. If the pool water is hard (high mineral content) the cell may require periodic manual
cleaning. To maintain maximum performance, we recommend that you open and visually
inspect the electrolytic cell monthly.
The following steps provide instructions on how to clean your cell.
Inspection and cleaning:
1.
Switch off the unit, unplug the power cord from the electrical socket.
2.
For filter pumps with 1-1/2” (38mm) hose size -
Turn both plunger valve handles fully
clockwise until they stop. This closes the valve, prevents the water from flowing out of the
pool.
3.
Disconnect the 2 hoses from the Ozone & Saltwater System, and attach the cell covers
(11)
to the inlet and outlet of the electrolytic cell
(9)
.
Connection Ridge
Locator Notch
Hinge
16


Need help? Post your question in this forum.

Forumrules
1

Forum

intex-zs6110-krystal-clear

Reset search

  • How do I take the cover off to get to the motherboard?
    Submitted Submitted on 7-7-2022 at 21:39

    Reply Report abuse
  • How do I take the cover off to get to the motherboard? Submitted on 20-6-2022 at 03:33

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex ZS6110 Krystal Clear at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex ZS6110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info