Manual Intex ZS6110 Krystal Clear (page 21 of 23) (English)

686153

Zoom out

Zoom in

1/23

(328PO) MODEL ZS6110 OZONE & SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2017

328

SAVE THESE INSTRUCTIONS

English

Page 21

TROUBLESHOOTING GUIDE (continued)

. Filter pump not attached to system

and/or switch on.

. Circulation line is blocked.

. Incorrect inlet and outlet hose direction.

. Scale on the flow sensor.

. Flow sensor cord is loose.

. Inner timer conflict between filter pump

and Ozone & Saltwater system.

. Flow sensor failure.

. Dirt or scale on titanium plates.

. Low salt level / No salt.

. Electrolytic cell cord is loose.

. Possible electrolytic cell failure.

. High salt level.

. LED display is off and the “SERVICE”

light is on - the system does not power

up.

. Caused by high humidity.

. PCB failure.

. Ozone generator assembly failure.

• Ensure filter pump is attached and operating.

See "Setup Instruction".

• If your unit has plunger valves, ensure that

they are open.

• Clear your filter cartridge and cell from debris

and dirt. See “Maintenance”.

• Release all trapped air in the circulation line.

See the filter pump manual.

• Check the direction of the inlet and the outlet

hose. Reverse the hoses if necessary. See

“Set Up Instructions”.

• Clean the flow sensor, paying special attention

to the hinge. See “Maintenance”.

• Plug the flow sensor firmly into the flow sensor receptacle.

• Reset both timers on the filter pump and

Ozone & Saltwater System.

• Contact Intex Service Center.

• Remove the electrolytic cell for inspection.

Clean it if necessary. See “Maintenance”.

• Add salt. See “Salt & Pool Water Volumes”.

• Ensure that the cell cord is plugged firmly into

the cell housing receptacle.

• Contact Intex Service Center. Replace the cell if needed.

• Partially drain the pool and refill it with fresh

water. See “Salt & Pool Water Volumes”.

• Household voltage is too high or too low (+ 20%).

Check the voltage is within the range stated on the

device housing.

• Run the system during midday and avoid running it

during dawn, foggy or raining time. Place a piece of

tile or similar pad, 15”x15” (38x38 cm) in size,

between the device and the ground to keep ground

water evaporation away from the system.

• Contact Intex Service Center.

LED PANEL

CODE

PROBLEM

SOLUTION

LED Panel Code Flash & Alarm On (

NOTE:

Always turn off the power before cleaning and servicing).

How do I take the cover off to get to the motherboard?
Submitted Submitted on 7-7-2022 at 21:39
Reply Report abuse
How do I take the cover off to get to the motherboard? Submitted on 20-6-2022 at 03:33
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Intex ZS6110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Intex ZS6110 Krystal Clear Manual

Product: