784581

Intex SSP-H-10 PureSpa Manual

22
Zoom out
Zoom in
Previous page
1/27
Next page
346
PO
S AVE THESE INSTRUCTIONS
(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019
English
Page 22
Spa Tub Drainage
1. Turn off the spa control unit.
2. Connect the drain valve adaptor to a garden hose and point the other end
of the garden hose to a suitable draining area (see drawing 14).
3. Remove the drain valve cap from outside of the spa tub and attach the
drain valve adaptor to the drain valve (see drawing 14).
4. From inside of the spa tub, open the drain valve cap, water will start
fl owing out from the garden hose.
5. When the water stops draining, disconnect the spa control unit from
the spa tub wall. Lift the spa tub wall from the side opposite the drain,
leading any remaining water to the drain and emptying the spa completely
(see drawing 15).
6. Attached the infl ation hose (7) to the air blower infl ation outlet on the
control unit.
7. Turn on the spa and press the button, aim the infl ation hose at the
inlet/outlets on the spa tub and spa control unit to dry out any water in the
piping system
(see drawings 16 & 17).
8. Use a clean towel to wipe up any remaining water and moisture on the
spa tub and spa control unit.
9. Ensure the spa tub and spa control unit are thoroughly dried.
NOTE: The enclosed plugs (15) can be used to cover the water inlet and
outlet connectors from the inside of the spa tub to prevent water from
fl owing out.
Spa Tub Cleaning
If dirt is visible in the water or water becomes cloudy and proper water
chemistry does not clear it up, change the water and clean the spa tub.
See “Spa Tub Drainage” section on how to drain the spa.
While empty, remove the cartridge housing from inside of the spa tub wall,
clean and/or replace the fi lter cartridge. Use a sponge and mild soap solution
to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly
before refi lling with clean water.
IMPORTANT: Do not use steel wool, hard brushes or abrasive cleaners.
Spa Tub Air Valve Fastening
Check the spa tub air valve for leakage and tightness before use. If air is leaking from the air valve, use the
provided wrench (22) to tighten the air valve as follow:
1. Make sure the spa tub is defl ated, open the air valve cap and insert the
wrench
(22) into the air valve body (see drawing 18).
2. With one hand, hold the backside of the air valve base from the inside of
the spa tub wall and turn the wrench (22) clockwise.
IMPORTANT: Never adjust the air valve base when the spa is in use or
fi lled with water. Only use the air valve wrench if the air valve is loose or
there is leakage around air valve base. Do not over tighten the air valve:
over tightening can damage the valve. Just ensure the air valve is snug
and not leaking.
MAINTENANCE
18
22
14
1
2
3
11
16
17
7
7
15
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SSP-H-10 PureSpa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SSP-H-10 PureSpa in the language / languages: English as an attachment in your email.

The manual is 3.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info