686578

Intex PureSpa - 28492 PS-BH-20 Manual

18
Zoom out
Zoom in
Previous page
1/34
Next page
344
NLA
S AVE THESE INSTRUCTIONS
(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019
English
Page 18
SPA CONTROL PANEL
J: Heater Duration Timer (HDT) Button
K: Celsius/Fahrenheit Toggle Button
L: Decrease Button
M: Increase Button
N: LED Display
OPERATION (continued)
Heater Duration Timer (HDT) Button: Use this button to select the desired length of time the
heating system should operate. Press this button and then press or to set the number
of hours you wish the heater to operate before it automatically turns off, from 000 to 048 hours.
The icon will fl ash red for a few seconds and then stays red. The heating system will operate
for the amount of preset hours only. The timer takes priority over temperature, so the heater
will shut off when HDT time runs out regardless if the preset spa water temperature is reached
or not. During the HDT function, the information shown on the LED display alternates between
the remaining heater operating hours and the water temperature. Repeat previous steps to
reprogram this function. To deactivate the function at any time, simply set the HDT time back to
000. To readjust the preset hours, press the HDT button twice and adjust the hours with and
buttons.
Example 2: Using the same scenario as example 1 above but rather than manually turning the
heater off when you are fi nished, you would like the heater to turn off automatically on Saturday
evening at 9:00pm. After going through the steps in example 1, press the HDT button and then
the or button to select 048 hours. The heater will then run from Thursday at 9:00pm to
Saturday at 9:00pm.
NOTE: If HST and HDT timers are both set, the LED display will fi rst alternate between
remaining time before the heater start and the water temperature, until HST timer runs out and
the heater activates. Then the LED display alternates between remaining HDT time and water
temperature until the HDT timer runs out as well.
Celsius/Fahrenheit Toggle button: The temperature can be displayed in either Fahrenheit or
Celsius. The system’s default is Celsius.
NOTE: The default temperature is 20°C (68°F). Temperature adjustment ranges from 10°C
(50°F) to 40°C (104°F).
NOTE: The spa control panel is resistant to water, but it is not designed to be completely
submerged. Do not put the control panel in the water. Submersion could cause water to enter
the panel causing damage to the electronics.
Adjustment Buttons: Press the increase or decrease buttons to adjust the desire function
settings. Press and hold the button will rapidly increase or decrease the numbers.
LED Display: Once plugged in the LED displays the current water temperature automatically.
If the control panel (3) is not placed on the control base recessed channel, the LED display will
go blank after 5 minutes. Press any button to resume the control panel.
L
M
N
JK
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa - 28492 PS-BH-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa - 28492 PS-BH-20 in the language / languages: English as an attachment in your email.

The manual is 5,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa - 28492 PS-BH-20

Intex PureSpa - 28492 PS-BH-20 User Manual - German - 34 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - Dutch - 25 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info