Manual Intex PureSpa - 28492 PS-BH-20 (page 17 of 34) (English)

686578

Zoom out

Zoom in

1/34

344

NLA

S AVE THESE INSTRUCTIONS

(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019

English

Page 17

SPA CONTROL PANEL

G: Sanitizer Button

H: Heat Button

I: Heater Start Timer (HST) Button

OPERATION (continued)

Sanitizer Button: Use this button to activate and set operating hours for the sanitation

system.

Heat Button: Press this button to activate the heating system. Press or to set the

desired water temperature. The heater will continuously heat until the water temperature

reaches the set temperature and then hold at that temperature. This is achieved by the heater

restarting automatically whenever the water temperature drops 1-2°C (1.8-3.6°F) below the set

temperature. When the ﬂ ame icon on the display is red, the heating system is activated. When

the ﬂ ame icon turns green, the water is at the set temperature. The heating system is then at

rest, but the ﬁ ltration system will continue circulating water nonstop, unless manually turned off.

If the heating system is reactivated, the ﬁ lter pump will restart at the same time.

NOTE: To stop the ﬁ ltration system while the heater is at rest mode, press the ﬂ ame button

ﬁ rst and then the ﬁ lter button. Pressing the heat button only while the heater is at rest mode will

turn off the heating system only and the ﬁ ltration system will operate for 1 more minute before

it turns off or continue with the ﬁ lter pump preset operating hours. To turn the heater off while

heating, press the ﬂ ame button.

IMPORTANT: The following conditions will lead to slow water heating:

• The ambient temperature is lower than 50ºF (10ºC).

• Outdoor wind speed is above 8-12 mph (3.5-5.4 m/s).

• The jet or bubble function is activated when heating the spa water.

• The spa is not properly covered with the spa cover when the water is heating.

Heater Start Timer (HST) Button: Use this button to select a future start time for the heating

system. Press this button and then press or to set the number of hours by which you

wish to delay the start of the heating system, from 000 to 120 hours. The icon will ﬂ ash red for a

few seconds and then stays red. The information shown on the LED display alternates between

the remaining hours before heater start and the water temperature. Once the countdown timer

reaches 000, the heating system will start operating. To deactivate the function at any time,

simply set the HST time back to 000. To readjust the preset hours, press the HST button twice

and adjust the hours with and buttons.

Example 1: It is 9:00pm Monday evening and you would like the spa to be hot on Friday

evening. Allowing for 24 hours for the spa to heat up (4 persons model about 1.5-2.5ºC (3-4.5ºF)

per hour) the heater should be set to start on Thursday evening. With the Spa turned on, ﬁ rst

press the Heat button and set your desired temperature. Press the HST button and then

or until 072 hours is shown. The heater will start after 72 hours has passed (Thursday at

9:00pm) and will run until the desired temperature is attained. The heater will then cycle on

and off to maintain the set temperature until turned off. To turn off the heater, press the ﬂ ame

button.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa - 28492 PS-BH-20 in the language / languages: English as an attachment in your email.

The manual is 5,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa - 28492 PS-BH-20

Intex PureSpa - 28492 PS-BH-20 User Manual - German - 34 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - Dutch - 25 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - French - 34 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Intex PureSpa - 28492 PS-BH-20 Manual

Product: