686578
10
Zoom out
Zoom in
Previous page
1/34
Next page
344
NLA
S AVE THESE INSTRUCTIONS
(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019
English
Page 10
SET UP (continued)
Humidity is a natural side effect of indoor spa installation. The room shall be properly ventilated to allow
moisture to escape. Install a ventilating system to prevent excess condensation, moisture in the room.
Additional requirements for outdoor installation
Spa owners may need to comply with local or states laws relating to childproof fencing, safety barriers,
lighting, and other safety requirements. Contact your local building code enforcement of ce for further
details.
Make sure the surface is level, at, smooth and strong enough to support the full weight of the lled spa.
Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and
damage the spa oor.
Do not expose the spa to direct sunlight for extended period of time. Provide protection from the
sun such as sunshade, tent, awning or gazebo.
It is possible to install and leave the spa outside at a temperature not lower than 4°C (39°F) provided the
water temperature inside the spa is higher than 4°C (39°F) and the water inside the circulation system,
pump, pipe are not frozen. Put a “temp barrier mat” between the spa oor and the ground to prevent heat
loss from the bottom of the spa and to provide better heat retention. Do not use the spa if the ambient or
water temperature is 4°C (39°F) or lower.
Setup the spa with at least 2 persons.
1. Move the entire package to the selected site. Do not drag the spa tub across the ground as this can
cause damage and leakage.
Open the carton carefully as this carton can be used to store the spa during long term storage or when
not in use.
2. Lay out all the parts on the ground and make sure all the parts are accounted for. For missing or
damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service
Centers” sheet.
Spa Control Panel Charging and Installation
1. Make sure the back of the control panel (3) and the control base recessed channel surface are clean and
dry.
2. Make sure the control base is plugged in and the RCD tested. Place the control panel (3) on the control
base recessed channel to charge the built-in battery (see drawing 1). See “Spa Control Panel” operation
section for more details.
3. Once the control panel battery is fully charged, you may place the control panel on top of the spa tub wall
(see drawing 2.1). To remove the control panel from the spa tub, lift the latch while pulling the control
panel away from the support stand (see drawing 2.2).
1
32.2
3
2.1
1
2
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa - 28492 PS-BH-20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa - 28492 PS-BH-20 in the language / languages: English as an attachment in your email.

The manual is 5,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa - 28492 PS-BH-20

Intex PureSpa - 28492 PS-BH-20 User Manual - German - 34 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - Dutch - 25 pages

Intex PureSpa - 28492 PS-BH-20 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info