Manual Intex ECO 6110 (page 11 of 27) (English)

686155

Zoom out

Zoom in

1/27

(329PO) MODEL ECO5110&6110 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2017

329

SAVE THESE INSTRUCTIONS

English

Page 11

SALT & POOL WATER VOLUMES

• Which kind of salt to use:

Use only Sodium Chloride Salts

Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also acceptable to use

water conditioning salt pellets (the compressed forms of evaporated salt). However, it will take a

longer time for them to dissolve.

Do not use iodized or yellow (yellow prussiate of soda) colored salt.

Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine. The purer

the salt the better the performance of the electrolytic cell.

• Optimum Salt Levels

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million). The optimal

level is 3000 ppm.

A too low salt level will reduce the efficiency of the Saltwater System and result in low chlorine

production. A high salt level may generate a salty taste to the pool water (this may occur at a salt

level above 3500-4000ppm). Too high a salt level may damage the power supply and cause

corrosion to the pool metal fixtures and accessories. The Salt Table page of this manual, shows

the correct dosage of salt needed. The salt in the pool is constantly recycled. The loss of salt is

due only to pool water being physically removed from the pool. Salt is not lost due to

evaporation.

• Adding Salt

. Switch the filter pump on to start the water circulation.

. Keep the Saltwater System turned off.

. Determine the amount of salt to be added (see “Salt Table”).

. Evenly spread the proper amount of salt around the inside perimeter of the pool.

. Avoid clogging the filter. Do not add salt through the skimmer.

. Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the

bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.

. After 24 hours and if all the salt is dissolved, turn on the Saltwater System, press

button

until you hear a “beep”, code “00” flashing and set the saltwater pool system to desired

operating time (see “Operating Time Table”).

• Removing Salt

If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm Codes”).

You will need to lower the salt concentration. The only way to do so, is to partially drain the pool

and refill it with fresh water. Drain and refill approximately 20% of the pool’s water until the “Code

92” disappears.

• Pool Volume Calculation

Rectangular

Length x Width x Average Depth x 7.5 Length x Width x Average Depth

Circular

Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79

Oval

Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80

Types of Pool

Gallons

(pool size in feet)

Cubic Meters

(pool size in meters)

I have ECO 6110 and keep getting error 91. Have too much salt 6.5 mpp but shows as low salt (that's how too much salt was put in)do I need a new eco electrode or titanium electrode. Or both or a new system? It is about 4years old Submitted on 26-5-2022 at 20:27
Reply Report abuse
Have model eco6100 the working and boost lights are on but no codes in red led box just a dot system will not shut off and no fault lights are shown what is the problem Submitted on 31-5-2021 at 02:34
Reply Report abuse
Yeah I have an Intex model eco6110 is there a sensor that tells how much salt there is the level and which one is it is it the ECO OR the titanium because I keep getting low salt codelite and the water is pretty salty help Submitted on 21-7-2020 at 04:12
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Intex ECO 6110 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Intex ECO 6110 Manual

Product: