752348
35
Zoom out
Zoom in
Previous page
1/38
Next page
(159) MODEL CS20110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/18/2012
159
SAVE THESE INSTRUCTIONS
Page 35
English
TROUBLESHOOTING GUIDE (continued)
1. Circulation line is blocked.
2. Incorrect inlet and outlet hose
direction.
3. Scale on the flow sensor.
4.Flowsensorcordisloose.
5. Device is set and operating in
backwash, rinse or waste mode.
6.Flowsensorfailure.
1. Dirt or scale on titanium plates.
2.Lowsaltlevel/Nosalt.
3. Electrolytic cell cord is loose.
4. Possible electrolytic cell failure.
1.Highsaltlevel.
2. Possible electrolytic cell failure.
1. Display and all lights are off - the
system does not power up.
• If your unit has plunger valves, ensure
that they are open.
• Clear your basket and cell from
debris and dirt. See “Maintenance”.
• Depress the 6-way valve, release all
trapped air in the circulation line.
• Check the direction of the inlet and the
outlet hose. Reverse the hoses if
necessary. See “Set Up Instructions”.
• Clean the flow sensor, paying special
attention to the hinge. See
“Maintenance”.
Plug the flow sensor firmly into the flow
sensor receptacle.
• Ignorethealarm,finishthebackwash,rinse
or waste operation then turn the power
switchOFFandONagaintoresetthealarm.
Contact Intex Service Center.
Remove the electrolytic cell for
inspection. Clean it if necessary.
See “Maintenance”.
Add salt. See “Salt & Pool Water
Volumes”.
Ensure that the cell cord is plugged
firmly into the cell housing receptacle.
Contact Intex Service Center. Replace
the cell if needed.
Partially drain the pool and refill it with
fresh water. See “Salt & Pool Water
Volumes”.
Contact Intex Service Center. Replace
the cell if needed.
Householdvoltageistoohighortoolow
(+20%).Checkthevoltageiswithinthe
range stated on the device housing.
Contact Intex Service Center.
LED PANEL
CODE PROBLEM SOLUTION
LEDPanelCodeFlash&AlarmOn(NOTE: Always turn off the power before cleaning and servicing).
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex CS20110 Krystal Clear at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex CS20110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 12,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info