595722

Intermec CN3e Windows Mobile 6.1 Manual

105
Zoom out
Zoom in
Previous page
1/148
Next page
Chapter 4 — Troubleshooting and Maintaining the CN3
CN3 Mobile Computer User’s Manual for Windows Mobile 6.1 93
Problems Reading Bar Codes
Problem Solution
You cannot see a red beam of light from
the imager when you press the Scan
button and aim the imager at a bar
code label.
• You may be too far away from the bar code label. Try
moving closer to the bar code label and scan it again.
• You may be scanning the bar code label “straight on.”
Change the scanning angle and try again.
• The scanner hardware trigger might be disabled in
Intermec Settings. To check the setting go to Start >
Settings > System Tab > Data Collection > Scanner
Settings. Hardware trigger should be checked.
The input device attached to the
computer does not work well or read
bar code labels very quickly.
Set the Scanner Model parameter to the specific attached
input device. Check the enabled bar code symbologies
and enable only the symbologies being used.
When you release a Scan button or
handle trigger, the Good Read LED
does not turn off.
The Good Read LED remains on if you configure the
computer to use continuous/edge triggering. If you
configure the computer for level triggering and the Good
Read light remains on, there may be a problem. Press one
of the Scan buttons or pull the trigger again without
scanning a bar code label. If the LED stays on, contact
your local Intermec representative.
The scanner will not read the bar code
label.
• Aim the scanner beam to cross the entire bar code
label in one pass. Vary the scanning angle.
• Scan a known good bar code label. Compare the two
bar code labels to see if the quality of the troublesome
bar code is too low. You may need to replace the label
that you cannot scan.
• Open Intermec Settings and make sure the bar code
symbology is enabled and configured correctly.
• Make sure the computer application is expecting
input from a bar code. You may need to type this
information instead.
The scanner does not read the bar code
labels quickly, or the scanning beam
seems to be faint or obscured.
The scanner window may be dirty. Clean the window
with a solution of ammonia and water. Wipe dry. Do not
allow abrasive material to touch the window.
You scan a valid bar code label to enter
data for your application. The data
decoded by the scan module does not
match the data encoded in the bar code
label.
The computer may have decoded the bar code label in a
symbology other than the label’s actual symbology. Try
scanning the bar code label again. Make sure you scan
the entire label.
… 105 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intermec CN3e Windows Mobile 6.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intermec CN3e Windows Mobile 6.1 in the language / languages: English as an attachment in your email.

The manual is 6,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info